Jump to content
The Klipsch Audio Community

Technical/Modifications

Talk about updating & modifying older speakers and other technical/electronic information here.

22401 topics in this forum

    • 32 replies
    • 11782 views
    • 247 replies
    • 152467 views
    • 286 replies
    • 36118 views
  1. Jubilee Schematic for passive crossover 1 2

    • 23 replies
    • 5491 views
    • 16 replies
    • 10475 views
    • 8 replies
    • 60 views
    • 10 replies
    • 153 views
    • 9 replies
    • 160 views
  2. Giant ported La Scala?

    • 15 replies
    • 239 views
    • 46 replies
    • 7935 views
  3. Cornwall repair?

    • 16 replies
    • 199 views
  4. 396s box build & modify

    • 8 replies
    • 138 views
    • 24 replies
    • 20306 views
    • 34 replies
    • 1535 views
  5. PPSL build? 1 2

    • 37 replies
    • 707 views
    • 2 replies
    • 82 views
    • 4 replies
    • 212 views
    • 32 replies
    • 6542 views
    • 50 replies
    • 1183 views
    • 735 replies
    • 64197 views
  6. KLF-10 Crites Mods

    • 9 replies
    • 465 views
    • 26 replies
    • 662 views
    • 89 replies
    • 15341 views
    • 4 replies
    • 107 views
    • 17 replies
    • 340 views
  • Recent Posts

    • All textured paint is harder to clean and the roller for Duratex does just that. Brushing it on will leave brush marks but be much easier to clean. I have to think spraying is best but have yet to try that. When I do I will report on what I find.   If you mix just s tad of water in the Duratex it will roll on with less texture but don't over do it.
    • If I can just teach that frog to make biscuits, she's outa here.
    • Dang Tom, I just went to get a tape measure, came back and saw your post. And yes it's 5 inches. Subtracting the thickness of the plastic it's 4.75 inches. And it measures like it would fit into a 13 1/2 by 7 inch cut out.
    • A man and his wife were going to take a ride in a horse driven carriage when the horse bucked up and whinnied. The man got out of the carriage and went to the front of the horse and looked him in the eye and he said, "That's one". He went back into the carriage and immediately the horse whinnied and bucked up. The man went to the front of the horse again looked him in the eye and said, "That's two". He went back into the carriage and the horse whinnied and bucked up again. The man went back to the front of the horse and pulled out his gun and shot the horse in the head. The man went back into the carriage and his wife asked him why he shot the horse. He replied, "That's one". JJK
    • You Guys are doing the  OP a disservice. He asked a simple question. I have a current version of the K-510 horn (the one currently sold and having the "mumps"). At the mouth the thickness of the material is 1/4 inch, The outside width is just shy of 15 inches. The outside height is just shy of 9 inches.    The width from the center of the hole to the other hole center is 14 1/4 inches in width (the holes are near the end of the "flare"). The height from the center of the holes is 8 1/4 inches. (vertical holes are about a little over 5/8 inch from the center of the hole to about where the flare ends)   The depth (from the face of the mouth to the back of the throat is 5 inches).    I hope this helps. It sounds like you have a project in mind. Please note that the K-510 horn (current version) is quite light. If you had a heavy driver mounted to the throat and the mouth mounted to the baffle, you might damage the face of the horn (the mouth-flange).    Good Luck, -Tom
    • I was thinking if she was up to her elbows....
    • Guess nobody has heard one.  About equivalent on the net.
    • Sent from my iPhone using Tapatalk
    • that's the definition of good meal.     you had to eat the oranges, on Kauai, outdoors or over a sink/bathtub.  You will have juice running off your elbows....  Never thought of sleeves. Nobody wears them.   Oh hey Here's a study we paid for it has been determined that people with ADHD are involved in more car crashes..  Ya think?    If it wasn't our money, I would laugh.
    • I love it when she "crawls along on her belly."  
×
×
  • Create New...