Jump to content

whatever55

Regulars
  • Posts

    713
  • Joined

  • Last visited

Posts posted by whatever55

  1. 4 hours ago, 000 said:

    it would be nice if you could keep the Amp and tuner , as well as a pair of Belles for Gil  ,  once he gets better , he may not be too happy to hear that all his gear is gone --but with a pair of stereo speakers and amp and tuner , that may just be what he needs -

    Maybe not room for the Belles but the electronics with either headphones or smaller speakers.... music can be very good   as you all know.

    • Like 3
  2. 3 hours ago, RandyH said:

    great deal for someone in California  , super condition ----glwts

    Agreed... ship to ny would be a killer....

     

  3. On 8/8/2021 at 12:07 AM, Vectra said:

    These sold and shipped:

     

     

     

    Joe Turner - The Midnight Special - PACD-2310-844-2 - NM/EX (two art retainer point impressions) $5
    Joe Turner - Joe Turner + Rockin the Blues (Collectables 2-fer) - VG+/NM $5
    Strawberry Alarm Clock - Incense & Peppermint - VG+/NM - $4
    The George Wallington Quintet - Jazz For the Carriage Trade - SACD Analogue Productions ‎– CPRJ 7032 SA, Prestige ‎– 7032 VG+/NM (light scuff/scratches you can't feel on disc size of 25cent piece $25
    The Zoot Sims Four - The Innocent Years - OJC - NM/NM - $9
    Mason Williams & Mannheim Steamroller - Classical Gas - EX/NM - $9

     

    Got them the other day.... arrived in good condition

  4. On 7/29/2012 at 3:20 AM, Chris A said:

    Sound stage width and height, in addition to reproduction presence, is what you'd be missing in addition to crisp percussion strikes. Once you've heard time-alignment in A-B with incorrectly aligned speakers, you'll not soon forget the experience.

    When you get to small groups such as jazz, blues, smaller classical ensembles,and folk groups, the effects of small time delay differences can be heard clearly, especially with sounds that are impulsive like drum sets and other percussion. Some of the most demanding recordings that I have is of percussion ensembles with string orchestra accompaniment. Others include violin and pianoforte concerto and solo instrument recordings.

    Nothing other than time alignment of drivers/horns can remedy the effects of misalignment. If you listen to a full-range driver system, you'll also hear the effects of time alignment except that in this case you'll also have to endure significant amounts of FM and AM distortion during musical peaks, reproduction of bass with hfs, and louder passages to hear the time-alignment effects.

    Chris

    So is this time alignment something new ???   was it not here in K-Horns . Belles, LaScalas ???   or was there a delay in the passive crossovers ?

     

  5. the front and back have 4 holes...   is that a 2 piece ring ?     also what is the difference between the early version and if there is one the newer version ?

  6. How about this    

    https://transcendentsound.com/pi-music-server.html

    Transcendent Sound       Vacuum Tube OTL Audio Amp Kits

    Build a Raspberry Pi 4 Music Server

    High End Performance for under $150.

    Not a Kit.  DIY Project to Share

    DSC_0057.jpg

    How would you like to build a music server that rivals those that cost over 10 times as much for less than $150.  This project (not a kit) will get you there.  The performance is outstanding.  It's so good, it allows digital sources to finally reach the sound quality it always was meant to have.  The sound is much closer to vinyl, and that is with standard 44.1 kHz, 16 bit sources.  Hi res digital should sound even better.  

     

    Here are the ingredients:  

    Raspberry Pi 4 computer, 4 gig                   $55

    HiFiBerry DAC + Pro                                      $40

    Raspberry Pi 4 3A power supply                  $15

    32 gig high speed (100MB/sec) micro SD  $12

    Pi fan                                                                   $5

    Misc Pi hardware                                              $5

    total                                                                     $132 (plus shipping and taxes)

    (also needed is a USB hard drive which most people already have)

     

    Here is how to build it.  For the base, any type of material can be used.  Shown is a scrap piece of 3/8 hardwood.  A fan must be used.  The assembly will get rather hot.  The heat goes into the circuit board so the best place to mount the fan is underneath and have it blow upwards.  This knocks the board temperature down about 35 degrees F.  

     

     

     

     

     

     

     

     

     

    The board should be about 20 mm or 3/4 inch above the base so air can freely flow around it.  Pi hardware is 2.5 mm with .45 mm screw pitch.

     

    Now for the operating system (OS) installation.  First make sure the SD card is properly formatted, FAT32.  (32 gig is the maximum size for the Pi) Best to use a dedicated formatter freeware program like

    SD Card Formatter

    Now download the operating system to your desktop computer.  This project is using Volumio.  It is also freeware but they have upgrades with subscription options.  It is zipped so it must be unpacked first.  For more detail about the OS, please refer to their website.

    Volumio

    Next, flash the Volumio to the mico SD card.  This is not the same as copying a file.  It requires another freeware program called balenaEtcher

    balenaEtcher

    Now flash the Volumio to the micro SD card.

    Connect the hard drive and an ethernet cable to the Pi.  Plug in the power supply. Give the OS about five minutes to cook.

    This OS is headless.  No keyboards or monitors are necessary.  It uses any smart phone or tablet to control it.  An internet browser is used for operation.  This allows for complete remote control.  The control device and the Pi must be on the same WiFi network.  The OS generates a WiFi hotspot which is used to connect to your network.  Once connected, the ethernet cable can be removed.

    There are many configuration options.  There are plug-ins for various streaming services and features.  The OS can use a network hard drive if desired.  The Pi USB ports cannot supply much current.  They can power only one hard drive.  There isn't enough current for a CD reader.  A USB hub would then be necessary (untested for this build, nor has CD ripping been tested).  New CD's can be ripped by plugging the hard drive into your desktop if desired.

    That's the whole thing!  It costs next to nothing and provides true high end performance.  Please join us on the forum for relating your experiences with this project.

    DSC_0056.jpg
    DSC_0055.jpg
     

     

    DSC_0057.jpg

    • Like 1
×
×
  • Create New...