dbert

Get a good magnifying glass and some good light and look at the pins real close. It’s a small slot with super small pins. Does the jack feel loose on the board? If you don’t find anything bent or loose the pins may just need a cleaning. A good (plastic safe) contact cleaner or deoxIT with the right brush would be ideal, but alcohol and an acid brush might work.

I just thought I would chime in with an update. Seven or eight months later and mine are still working fine. I still have never used the standby function for any long duration though.

This is the other side, but same points.

Sorry for the delay. It will be at least one more day before I will be able to try this.

Im listening!

Wait. What end were you having to hold a certain way to make it work? The dock or the amp/sub? Sorry. Reread what you said. Dock end. Disregard.

I have some promedias that had a problem with the Din connector. If the pins look ok check the the printed circuit poard to Din connection for broken solder joints. http://forums.klipsch.com/forums/p/113932/1147209.aspx#1147209

This is bad news. This means it's not just a vendor choice for the original capicators, but a design flaw that kills capicators.

Interesting. I have not used the standby feature for more then a few seconds at a time since I replaced the capacitors. I've left it powered up for how ever many weeks it's been now, but have just turned the volume all the way down or turned off the audio source. I seriously considered disabling the standby button when the dock was apart, but you need it to turn the unit on after power-up (make the led fwd of vol wheel (knob in my case) green). Keep us updated. I wish I had an occiliscope to see what goes on in standby.

It may well be that the one 25V cap is all we needed. The 4 larger capacitors are used by the 18 volt 5 amp transformer output (yellow/black/yellow wires), and this one smaller cap is for the 10 volt 1 amp winding (pair of brown wires). It appears this 10 volt circuit is what feeds the dock. Rather certain these are just AC to DC power supply rectifier smoothing capacitors. If they are crap though, I am glad I changed the other 4 also. Bottom of board marked up to show basic paths.

By the way...for those looking for tips on how to DIY. This has some nice photos and info. http://www.capacitorlab.com/replacing-motherboard-capacitors-howto/index.htm

All the values look correct to me. Found a bunch of 63 volt cap photos here. Many similar but nothing exact. http://www.sportslinkup.com/shop/0-Capacitor-63v-1.html What makes you think they need replaced? Electrolitic capacitors built in the early to mid 2000 range are always suspect, but these? I fear you may be just making work for yourself. I could be wrong.

I'm wondering if this could be done internally to the dock. With all the test pionts to the 30 pin connector it looks like soldering some resistors in the right places could make it happen. http://pinouts.ru/PortableDevices/ipod_pinout.shtml Just need to find the right locations to solder stuff.

My Sub is all assembled. Do you have close-ups or can you tell us what is printed on them? The Evox Rifa type sound like a premium product.http://www.audiocap.net/EvoxRifa.htm I’m not 100% sure what happens with the mute/standby switch is selected but I’m going to avoid using it at all. I have my suspicions and I wish I had an oscilloscope. Sometimes I may think it will only be for a short duration (say the phone rings) but I may then forget and leave it like that overnight or something. Switching it off on the back would surely save electricity. As I said I’ve just been turning mine all the way down or turning off the source when not in use. Mine is real easy to turn down now.

Glad to hear this is working for others. Because these were so large I trimmed off a majority of the nubs on the bottom with some flush cut diagonal pliers first. Just to remove some of the lead and the bulk of the existing solder on the bottom side. I then heat “say” the positive lead as I put pressure towards the negative lead. When the solder is melted you can tilt the cap and pull existing lead thru the pcb a ways. Then I heat the other lead and put some pressure the opposite direction. Just walk them out one lead at a time. It can take a few back-and-forth’s on each one. I took them all out so I had more room to work cleaning up the holes and putting them back in. You just need to remember which side is positive and which is negative (with stripe). Also, when they are removed there is a little “+” symbol printed on the board under the cap showing polarity. I also use soldering braid to try to remove as much old solder as I can. Removing the old solder and opening up the holes is always the hardest part for me. Remember to be gentle going back in as you don’t want to force it and break the pad away on the board. See if there is some television repair guy still around. Look for some armature radio folks. They almost always have the tinkerer in their midst with the skills to do this. Put an ad on craigslist. I’d love to tell you to do it yourself. It’s not really that hard, but if you haven’t used the iron before you may want to find some junk motherboard or other electronic part and remove the caps and clean the holes there first. There is a lot of general soldering technique info on the web. I’m not going to risk putting mine in mute mode. I’ll just turn it down. I mounted a knob on my dock. It’s not real attractive but it’s much easier than the partial wheel.