Jump to content

JohnA

Heritage Members
  • Posts

    5916
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by JohnA

  1. The diaphragm for the K-77/K-77-M/E-V T-35/E-V T-350 can be bought in the U.S. for about $23. Many here have replaced them themselves. I have not, but it's not supposed to be hard. Go to a Pro Audio shop and ask about getting the diaphragm in a T-35 replaced and see what it'll cost. $100 is too high in the U.S. Klipsch will do it for $77. Blowing a tweeter in a La Scala with it's tweeter protection circuits in place indicates the speaker has been pushed too hard (or the attached amp has). Unless some other part has failed, I wouldn't worry about damage. Replacing the other diaphragms or reconing the woofer is relatively inexpensive, if one of those parts turn out to be damaged. The squawker diaphragm is about $55 and reconing the woofer in the U.S. is about $75. John This message has been edited by John Albright on 09-30-2001 at 12:50 PM
  2. Neither the LSI, nor the standard La Scala is in production at this time. You'll have to buy either used. Technically, there is no such thing as a "Home" La Scala. La Scalas were made for pro use either in clubs and theaters (what you call the home version) or for touring, the LSI. There were at least 2 configurations of the LSI, one and 2 piece. All of the LSIs I've seen pictured had handles. All were black with corner and edge protectors. I use 2 pair of La Scalas in my home theater, but they take up a lot of room and the rear pair is purely overkill. I *could* be persuaded to sell those. Your CE2000 is generally too powerful for one pair of La Scalas. Maybe if used to power 2 or 3 pair, it will be about right. If you use it, you will have to be very careful with your gain controls and prevent clicks, pops and squeals from feedback to keep from smoking some of the drivers. John
  3. You need to ask this in the Promedia forum. This is a home audio forum. John
  4. The RSW-15 has the guts and output to keep up with any of Klipsch' main speakers. It was more than enough to keep up with the Jubilees (108dB/w/m?) at what must have been 110 dB or more on the peaks when we watched The Matrix in Hope (it hurt). The system had Jubilees as mains, a Belle as Center and K-horns as rear surrounds, each channel has a 200 watt power amp; the gunshots were breathtaking! John
  5. It's a phase plug. I believe its ultimate effect is to smooth the response of the tweeter. I don't know whether the RF-7 should have a visible one of not. I'm sure it has one, but it may be deep in the driver behind the "bug screen". John
  6. I believe the HIP is a ported Heresy I for the pro market. The ones I've seen look to have the same drivers as the HI, except for the woofer. I'll bet that 92 dB rating is at 10 feet, too. That would make it a few dB louder than a normal Heresy. John
  7. It's difficult to know what to say. I'm still in shock and disbelief. I feel sorrow for the victims and anger at the perpetrators. It IS time the U.S. starts kicking somebody's butt and I'm not sure we should care about "collateral damage"; the terrorists didn't. Pray for the souls of the dead and families and rescue workers. John
  8. I'm glad I went, too! And just in case I forgot to say "Thanks" to somebody: Thanks a lot for the help organizing it (I could never have done it alone) and thanks for the great hospitality you gave us all! John
  9. I don't think the Hope plant will close. There has been talk of moving engineering and customer support to the new Indy HQ for about a year. I'd hope they'd wait until the school year is over, though. I'll bet that was the start of the rumor you heard. John
  10. M.H., The latest La Scalas have a the Type AL-3 crossover. It should be a very good crossover and I would be slow to replace it. The latest ones also have a fiberglass squawker horn that should not ring as much as the aluminum horns my La Scalas have. However, it took me about a year to "hear" the ringing I described. Once you notice it, it is obvious, but most people will not notice for a while. The same applies to the bass horn resonance. I normally notice it only on Seal's voice. John
  11. You should write to Klipsch to see if they will sell you a pair of K-55-Ms. They are no longer in production, so you might have to use another driver. The K-401 horn and K-33-E woofer are available. The K-33-E is about $US100. It is by far the best woofer for the La Scala's bass horn. The 2 have been tuned to each other over the years. John
  12. All I remember is the reviews said Soundcraftsman amps were harsh and dirty at low power, but sounded pretty good above 10 or 20 watts. John This message has been edited by John Albright on 09-03-2001 at 06:54 PM
  13. I have 2 pair of La Scalas. but unfortunately, have never seen RF-3s. Soundog has described the La Scalas very well. I think they have a few flaws and only one cannot be removed easily. The worst flaw is a ringing in the squawker horn. That is fixed by wrapping the squawker horn in rope caulk or other clay that will not harden or a product called Dynamat. The bass horn also suffers from some resonance affecting male voices, but it is subtle and not usually offensive. A horizontal brace across the bass horn would probably solve that problem. The tweeter is mounted the the rear of the baffle and "looks" through a 19mm deep "tunnel". This causes some harshness in the highs and is fixed by front mounting the tweeter. Klipsch makes "Z" brackets to do just that (the tweeter opening must be enlarged). Some of the 80s models had a really poor sounding crossover network (Type AL) and it has to be replaced. The newest, Type AL-3 or Al Klappenberger's crossovers are good replacements. Finally, the La Scala's bass horn begins to roll off at 60 Hz and little bass is present below 45 to 50 Hz. Nothing can be done for this, but buying subwoofers. The bass output is in proportion to the rest of the music and the result is very natural sounding, but they will not shake a room. That said, I will probably never be without a pair of La Scalas; I like them that well. Most of the flaws could be solved by Klipsch and I doubt if I surprised them with my assessment. However, the cost of my modifications on an assembly line would probably not be worth it.
  14. I run an Acurus ACT-3 for my Pre/Pro and an Acurus A-250 power amp for my subwoofers. My other amps are Parasound, a similarly priced and designed product. John
  15. JohnA

    Ksw-10

    Seb, Actually, it is because the sub has very HIGH impedance and therefore is almost "invisible" to the amp. The formula for parallel impedance is: 1/A + 1/B = 1/combined impedance. So, 1/8 ohms + 1/8 ohms = 2/8 ohms = 1/4 ohms. The total load is 4/1 ohms or just 4 ohms. If the sub's input impedance was 100 ohms the results would be: 1/8 + 1/100 = 100/800 + 8/800 = 108/800. Inverting 108/800 gives 800/108 = 7.4 ohms. That's an insignificant change to an amp. I'd even bet the sub's input impedance is more like 10,000 ohms, too. John
  16. Dynamat works well and is easy enough to apply (warm it first) to the metal horns. Rope caulk would work just as well, I think. I would use rope caulk on the fiberglass K-horn horns. Getting dynamat down into that waffle pattern would NOT be worth the work. I used Dynamat on my La Scalas' aluminium squawker horns and rope caulk on the tweeter horn. John
  17. Plugging the port will not damage anything and will reduce the bass output near the port's resonance. It might even increase the output at deeper frequencies, slightly. Try it. I've never seen a CF-2, so I don't know what else might be done. John
  18. $1000 is a fair price for La Scalas as described. That's what I paid for my first pair in worse shape that you describe. Of course, offer him $800 first. John This message has been edited by John Albright on 08-28-2001 at 04:11 PM
  19. The distortion could very well be from the voice coil rubbing. However, it would be almost impossible to remove the cone without destroying it in the process. If the voice coil is rubbing, causing your distrotion, it is rubbing because it has delaminated or something else has failed. Try to find somebody to recone your woofer. Since it is an SP-12, you should be able to find someone who can, or maybe another one in good shape. I've done a Yahoo search for speaker repair and found several. There's one in Knoxville, TN and a big one in CA. John
  20. I flush mounted a pair of my La Scala tweeters and it did improve the sound. I got more detail and clarity, less harshness in the highs. The brackets (one for each side) are available from Klipsch, but are a simple "Z" with 90 degree bends and a 3/4" (19 mm) offset to hold the tweeter flush with the front of the cabinet. The 4 screw holes that hold the tweeter to the cabinet are used with the brackets and wood screws hold the brackets to the inside of the cabinet. John This message has been edited by John Albright on 08-29-2001 at 08:16 PM
  21. The bass to mid xover in a La Scala is at 400 Hz. I've never seen data showing the upper end of the basshorn's response, but that 400 Hz crossover limits the squawker drivers that will work. Bruce, you're correct that most squawkers want to be crossed at 800 Hz or so. That's one thing that has kept me from creating my own 2-way La Scalas. PWK first made 2-way K-horns and lately the experimental home Jubliee is a 2-way design (the Jubilee has a new basshorn that is said to go up to 1000 Hz or so. The xover is at 800 Hz). I think if Mr. Paul could have made a 2-way La Scala, he would have. In pro audio, a tweeter that has a long term power rating of 2 watts is one that is just waiting to be blown. The La Scala, in particular is not the speaker to have used that tweeter if there was a way around it. John
  22. It could be your room, too reflective. Try some wall treatments. As an experiment, hang quilts on the side walls. If it works buy something attractive like Persian rugs. I have a -C7 and have listened to the KLF-20. I didn't find them harsh. I like them a lot. John This message has been edited by John Albright on 08-26-2001 at 06:15 PM
  23. From the serial numbers the HBRs are 1981 models and the HIP-2s look like 1986 models. 1981 was a transition year, so I'm not sure which squawker the Heresy had in 1981. That was the last year for the K-55-V in the larger Heritage models. The HIP-2s may well be Heresy II professional models. You'll have to open them up to see what drivers are in them before most of us can say whether they will soung much like your HBRs. I'll bet they do, though. John
  24. Gil's "Dope from Hope" shows a device to be used between a stereo preamp and 3 power amps at "line" level. A speaker level device would be much more robust. John
×
×
  • Create New...