Jump to content
The Klipsch Audio Community

Kelly McAloney

Regulars
  • Content Count

    157
  • Joined

  • Last visited

Everything posted by Kelly McAloney

  1. So, where's the sub, do we get to see[emoji851]
  2. Are you sure it's a single female at the other end? Should be a male. It actually does serve a purpose. There are some subs that will not work if you only plug in a single RCA. I don't understand it either since it is a mono signal. Maybe someone else can chime in why.im sure it is single female there is spicy above in another comment
  3. sorry youth not home and won't be for a couple days so right now no pic but it is about six feet long with 2 make rca at one end and1 female Eva at the other end, seems weird they would include it if it has no purpose [emoji17]
  4. is there any benefit to using this
  5. I bought a complete klipsch wiring kit, there is a cable that looks similar to a sub cable that has two male connections at one end and one female connection at the other, can anyone tell me what it's for? Thank u in advance;)
  6. Thanks buddy, appreciate the response [emoji106]Sent from my iPhone using Tapatalk
  7. Need some recommendations for an spl meter Sent from my iPhone using Tapatalk
  8. i got a little winky guy, like this[emoji12]I'm just trying to explain why the question came up and not to lose patience [emoji111]️Sent from my iPhone using Tapatalk
  9. Where can I get these[emoji849][emoji12]Sent from my iPhone using Tapatalk
  10. NO! As everyone here has mostly already said, there is no such thing as a meaningful "max." The VC isn't like a water faucet, with a pre-determined maximum outflow that all the other components could be designed to work with. If there was an industry standard for "max" (measured amplifier/receiver v. out), then you might be able to think of all-the-way-up as the reasonable "max" setting for that system. However, speaker efficiency is just one of the huge unknowns in this equation, probably makes an industry standard impossible.Lacking such a standard, one receiver's max can take the amp and speaker output beyond the moon and blow everything out, while another's might not do that. Depending on speaker efficiency, too. The industry will tend to go too far rather than fall short. With apologies for putting it this way, you are very unclear regarding just what "max" means. You would harm your setup if you took your concept seriously. Like blowing out all your woofers. I am not planing on doing this, I ask questions because I don't know the answer(have to start somewhere) the reason I ask, after I hooked up my new sub and receiver I had a friend that wanted me to turn it up all the way, I said no because I have no idea what would happen, so I got thinking about it and thought this would be a good place to ask, thanks for your feedback, sorry for making u angry [emoji12]Sent from my iPhone using Tapatalk
  11. I've always had trouble understanding this part of it but I think I'm coming around but still sways to go, I appreciate your response Sent from my iPhone using Tapatalk
  12. I run them as small with v1800 as backup, I do not plan on trying thisSent from my iPhone using Tapatalk Have you moved the sw-115 to another area, or did have you integrated it into your primary listening area?It is a 12, I put in the kids media room to help out there Polk 8", it sounds great with there system, rooms a lot smaller thoughSent from my iPhone using Tapatalk
  13. SPL meter. Most people blow speakers using underpowered amperage than overpowered. Also, You have to consider source material, if it has a lot of bass, it could damage the 10's in the RF7's. Will spl measure sound level and frSent from my iPhone using Tapatalk
  14. I run them as small with v1800 as backup, I do not plan on trying thisSent from my iPhone using Tapatalk
  15. This is definitely helpfulSent from my iPhone using Tapatalk
  16. How would I know where reference level is Sent from my iPhone using Tapatalk
  17. I wasn't considering doing it I was just curious, I've had them about 3/4 the way up and it was uncomfortable not to mention the sub knocks things off shelves at the other end of the house in the basement [emoji15] so then my question becomes why rate them that high if they can't handle this Sent from my iPhone using Tapatalk
  18. If my avr is 125 pet channel and my towers are 150rms, in theory could I turn the volume to max without damaging anything Sent from my iPhone using Tapatalk
  19. It can be. Sometimes the source material is recorded or broadcasted poorly and can add audible distortion.Does it happen very often with different sources? Bill so far just with my iPhone and I can only hear it on slower music I was thinking it was the Bluetooth because my kmc3 has some crackle sometimes but I was concerned because I could only hear it out one sideSent from my iPhone using Tapatalk Switch the channels the speakers are on (just move the cables, each to the other speaker), and see if the crackle changes sides.thats a great idea, I'll try that as soon as o get home and let u knowSent from my iPhone using Tapatalk Well I tried what u said and it didn't do it at all one of the banana plug was loose so I spread it a bit when I put them back to correct speaker and crackle is gone thanks for your help guys [emoji445][emoji344][emoji344][emoji344] Sent from my iPhone using Tapatalk
  20. It can be. Sometimes the source material is recorded or broadcasted poorly and can add audible distortion.Does it happen very often with different sources? Bill so far just with my iPhone and I can only hear it on slower music I was thinking it was the Bluetooth because my kmc3 has some crackle sometimes but I was concerned because I could only hear it out one sideSent from my iPhone using Tapatalk Switch the channels the speakers are on (just move the cables, each to the other speaker), and see if the crackle changes sides. thats a great idea, I'll try that as soon as o get home and let u knowSent from my iPhone using Tapatalk
  21. It can be. Sometimes the source material is recorded or broadcasted poorly and can add audible distortion.Does it happen very often with different sources? Bill so far just with my iPhone and I can only hear it on slower music I was thinking it was the Bluetooth because my kmc3 has some crackle sometimes but I was concerned because I could only hear it out one sideSent from my iPhone using Tapatalk
×
×
  • Create New...