Jump to content
The Klipsch Audio Community

Mitchibo

Regulars
  • Content Count

    30
  • Joined

  • Last visited

Community Reputation

6 Neutral

About Mitchibo

  • Rank
    Member
  • Birthday 09/17/1964

Profile Information

  • Gender
    Male
  • Location
    Georgetown Texas
  • My System
    Heresey III's reference.
    RP-450C center
    RP-240S surround
    RP-150M wides
    RP-140SA atmos
    G-16 flat panel height
    Denon AVR -X5200W
    Xbox 4K player
    Legrand power amp



Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Already have four RW112's. Looking for pure imaging and hopefully superior mids. I've got the low end covered.
  2. So other than a larger cabinet and woofer the H3's and the CW have the same upper end. So all that is gained is lower extension?
  3. I have a pair of H3's that I like but...I'd be interested in opinions comparing these with the Cornwall3's. Aaaaaand go..
  4. CHASLS2, how do you like it so far? I've been looking at this same model but it ain't cheap right now. It does look fantastic but boy I could use a good sale about now. Hurry up Best Buy!!
  5. Sub # 3 and # 4 arrived. Not sure I can fit and balance another speaker in here. 7.6.4. So Audessy, then pushing and pulling and sniffing for half-assed placement. Then measuring till my head explodes. I will be here on Dagobah till the force is strong within me. Carry on.
  6. Awww... good info Robo. Thanks for the link. I have my work cut out for me. This should be an addendum to REW 101.
  7. Logical. Running the sub through mini. Made tons of measurements and I've manage to flatten the response from a rise at 20 to +/- 5db to an 80 falloff. However, I'm not familiar with setting delays through mini. I can see my impulse response graph but I'm not sure how to "set" the delays. Currently REW measures the delay at 8.35 ms (9.4 ft) with an acoustic reference. Does the mini 2x4 HD allow manual delay options?
  8. AVC92, yup. It's just money. Help make America great again by spending your hard earned cash. Be patient and read carefully with the MiniDSP instructions and definitely use the tutorial. I jumped off the cliff and ordered two more subs. Now I'm wondering about whether to connect the front two together, back two together or the left back/front and right back/front? Two outs available on my Denon. Annnnnnd...go!
  9. Interesting info Robo. Since my last post I installed a few 4" panels behind MLP, up high pointing at angle downward. One to the left and one to the right. These are more ceiling treatments than wall treatments. After bobbing my head up and down and all over the living room I found that the wall/ceiling joint keeping a lot of woofy bass stuck up there. Also one vertical corning got a wedge bass trap. It didn't change the sound image radically but it helped eliminate that swirling eddy in the corner. I am taking yours and others advice on the MiniDSP. Gunna get the whole kit with mic and all. REW is loaded to the laptop as well as a 130 page tutorial. The measuring itself should be a breeze however it seems like most of the tutorial was dedicated to getting all the settings correct (mic recognition/calibration, sound card, etc.). Yeesh. Into the abyss I go. Recent update: Two R112's with MiniDSP corrections have proved to be the 8th wonder of the world. If two are great I assume two more would be really bitchin', no? Small room but who cares?
  10. Interesting info Robo. Since my last post I installed a few 4" panels behind MLP, up high pointing at angle downward. One to the left and one to the right. These are more ceiling treatments than wall treatments. After bobbing my head up and down and all over the living room I found that the wall/ceiling joint keeping a lot of woofy bass stuck up there. Also one vertical corning got a wedge bass trap. It didn't change the sound image radically but it helped eliminate that swirling eddy in the corner. I am taking yours and others advice on the MiniDSP. Gunna get the whole kit with mic and all. REW is loaded to the laptop as well as a 130 page tutorial. The measuring itself should be a breeze however it seems like most of the tutorial was dedicated to getting all the settings correct (mic recognition/calibration, sound card, etc.). Yeesh. Into the abyss I go. Lastly I have a question about that 3rd Klip110 sub I have left over. My 12's are placed symmetrically in the front. I have only three option if I wanted to integrate the 110. Option one would be to place it directly on my left of the MLP. This would be asymmetrical...all subs lined up in an "L" fashion firing to the center of the room, more or less. Option two would be to place it 8 to 10 foot to my right along the back, wall firing towards the center, also in an opposite "L" arrangement. Option three would be to pull the couch out from the wall 12 inches and stick it right behind it, but having to firing perpendicular, as in facing right or facing left. This would at least give me a triangular arrangement but it wouldn't be able to face forward towards the other subs. A couch is a pretty big bass trap. Thought? I may have to do subwoofer crawl but it would be nice to get others feed back so I don't waste a bunch of time. I assume I'd place the two front 12's on a "Y" splitter to accommodate number three in the Denon?
  11. Has anyone installed bass traps? Or experienced in acoustic treatments?
  12. Here's another stupid question. Has anyone stacked their main on top of their sub cabinet to conserve space?
  13. Thanks for the feedback. I learn something every time I read yawls posts. So here are a few more detail photos of my living room/listening area. It's pretty wonky. A lot of obstacles and a rock fireplace. This is all I have to work with so would using a MiniDSP as Rowan611 suggested (or didn't suggest) be useful in this situation? What I have is an improvement with the new subs, however we all want to squeeze out all we can from our systems. W/O a dedicated theater room would his be throwing money into a minicule improvement due to a weird room?
  14. Re did it. 9.5 sub off set. Another question. 2 channel play back has distance and level calculations. Obviously we keep those settings for HT but I tend to be seated in the middle of my listening area for 2 ch playback. So if I reset those distance and particularly the levels to match would that in any way affect the Audyssey HT calculations? Sometimes I use a music profile but I do like to run it pure as well. Not sure if pure bypasses Audyssey but it seems to as the levels are +- .5 Db Lt and Rt. vs -3.5/-7.5 Lt and Rt respectively.
  15. I assume then -12 is the max offset, turning the sub down, and recalculating with Audyssey will prevent sub over drive?
×
×
  • Create New...