Jump to content

VAZ019

Members
  • Posts

    7
  • Joined

  • Last visited

Everything posted by VAZ019

  1. One other note, the speakers in the other unit also showing 5.9. Would a difference between 5.7 and 5.9 ohms justify this sound disparity.
  2. So tried the other speaker as you mentioned, swapping drivers I'm getting same result in the working unit. These two drivers I bought are testing at 5.7 putting out less sound. I used my phone to show the difference. With Woofer unplugged. So only test speaker is running. Ran the 2 replacements i bought see blue 10 secs, green 10 secs, compared to red 10 secs. Without adjusting volume, there is the jump in volume. To the ear its a big difference.
  3. Loud means a level that is noticeably different without touching the volume knob. So a simple speaker swap in the same driver location of one rs3-II. The louder speaker tests the same as the other 3 speakers that I say are quieter. This is wierd. So all test 5.9 to 5.7. Good/bad loud/quiet Then because the rs3-II has two driver locations in one speaker. I can take the loud speaker and move it to either location in this same speaker. It will play at either location of what I call the loud level again without touching volume knob. The three suspect speakers will not and will be quieter, without adjusting volume. I can't see it being a crossover issue if the good speaker plays on either side at the same sound output. Unless it has something with when two drivers are trying to run.
  4. Hello All, So I bought a pair of used RS3-ii speakers mainly for the design. These have two K106-K tweeters 45 degree ish angle and a woofer in the center facing forward. I bought a pair which one of the tweeter would not generate sound. So I just went ahead and bought two additional used K-106-k divers. So I would have a spare. This is where it gets wierd. Neither of the two speakers I bought will generate loud sound compared to what I would call the working driver. I now have three K-106-K drivers that will not generate loud sound no matter what location they get installed in the pair of RS3-iII speakers I have. So I'm checking the location also with the one good speaker. Keep getting same result. 3 quiet speakers 1 that puts out loud sound. I break out the ohm meter and they all test good at 5.9, 5.7. Which I feel makes sense because they do produce sound. But why not volume? what are the chances of all 3 speakers having this issue. any insight as to what the problem would be?
  5. On the K28-E woofer. I thought this is a replacement for the newer H3's & H4's? My impression was the crites woofer was the way to go if you were replacing a K24 which is the rarer woofer. Something with the ohms. Isn't the newer H3's done different with the crossover. Regarding the topic of band pass crossover? So Trey says it isn't required. But then I ask why would crites sell this. Before I make a decision and drop more money. I have to ask what does this band pass crossover do if you switch to Ti diaphrams. There was a nice write up on these drivers and the range the crossovers/drivers are running between old H2's and the newer H3's& H4's. I'm guessing it has something to do with this. I don't want to have issues in future or mess something else up. Reminder my crossover is a KP-20A @ Trey, Can you send me info on the TI diaphram. I only received the PH diaphram info. Any insight on using the Ti's in K53. Should I be looking at the whole driver assembly. I would like some clarification as using the Ti's wasn't your first choice. Not the info fellas, thanks for the reply's
  6. Klipsch says to switch the diaphrams to the TI's a K53-Ti. Anybody out there made this switch? I'm waiting on a price for the parts. Anybody offer any insight on where al the Ti's are used? I am assuming in the new Hersey 3's and maybe IV's
  7. Looking for a replacement diaphragm or driver for a squawker for a set of Klipsch KP201's with Type KP-20A crossovers. From the trouble shooting side when I turn the volume up I loose sound. Lower the volume and horn turns back on. I think the connection is interrupted inside the diaphragm itself when vibration increases. I hooked up the squawker to a working speaker to rule out a crossover issue. I cannot find a replacement diaphragm anywhere, not much info on a K53-K, there is one K53-K driver on ebay and the guy won't ship, pickup only. Looking for some help on replacing the driver, driver and 701 horn in these. Anybody got any parts or recommendations of something I can go to. I am replacing the woofers with Crites speakers. (thanks Micahel). Appreciate the help.
×
×
  • Create New...