Search the Community
Showing results for tags 'alk csw'.
Found 2 results
I bought a pair of Heresy I’s in 1979 in college that have been w/ me ever since. Type E crossovers, K77 tweeters, K55-V squeaker drivers w/ K700 horns and K-22-E woofers. I replaced the K77s w/ new ones from Klipsch about 20 years ago when I blew them and I replaced the binding posts at the same time so I could use banana plugs and lower gauge speaker cable. Otherwise everything is original. I don’t hear any obvious problems with them, but I want to restore them to their former glory or better. I’ve been reading everything I can find here and at Crites and at ALK but I still have many questions and would appreciate advice. 1) I know I need new caps and since I don’t solder, I plan to replace the crossovers. I could use Crites Type E, which uses the same spec as the original, or ALK’s universal CSW which have some upgrades. A few questions about that: - I understand what Al says about constant impedance and no resistive error, but I don’t use an SAT amp so does that matter to what I hear? - Also, the Type E only uses a low-pass inductor for the woofer. The squawker and the tweeter use high-pass capacitors in parallel, so (if I understood Al’s site) high freq sounds that should only go to the tweeter go to the squawker too. Does that matter? Would it matter if I replaced the K77 tweeters w/ Crites CT120s? - Are the actual crossover frequencies the same between the two networks? It looks like maybe there is some adjustment possible on the CSW but I’m not sure. 2) Is upgrading the K77s to CT120s a good idea? 3) I know I need to replace the gasket between the squeaker driver and the squawker horn, but does it also make sense to upgrade the K-55-V with a Crites A-55G? Do squawker drivers wear out and/or is the A-55G a lot better? 4) Crites offers CW1228 woofers as drop-in replacements For the K-22-E. Are they better, especially given that the K-22-Es are 40 years old? Or what if I just rotated the K-22-Es 180 degrees as I read somewhere? Sorry about so many questions - I’ve read a lot on my own and I’m still not clear on the best way to do this. There is tremendous expertise here and I’d be grateful to tap into it. Thanks in advance
Hey everyone... did a rewrite of this to share more about the project Im working on. Ive been a fan of Klipsch and tube amps for a long time. Given my amp choices, horn or single driver speakers are the preferred choices. Normally I build big honking speakers... I even built one my wife kicked out of the house... too large. In an effort to finally get some speakers in the TV room I went after something she has accepted before... the Heresy. She has liked it before due to its limited height... it doesn't block the windows. I love it as, its a 1950s VW battle with a Porsche engine hiding under the hood. The Heresy is an honest 96db speaker. Good for 50hz or so on up. Its a sealed box so no bass hump. Its mid bad is solid and its a fast speaker. Id consider it a gateway drug. I went of CL in search of a local purchase. In a perfect world I would have found a gen 1 heresy. You want this type as it has the screw on K55 driver... the same mid range in other Klipsch speakers like the Cornwall, LaScala or K Horn. Unfortunately as I planed to gut the speaker and start over, the only one in my price point was beatup and a gen 1.5 Heresy. $400 later it was delivered to my door. The plan is to use a ALK Crossover. Its adjustable and will make a Heresy actually sound good. Attenuating the mid and HF is super important and I still have HF hear and want to keep it that way. The woofers as K22 are perfectly fine.. maybe even good, but the Eminence LFA12 is better and closer to the pro K24 spec. The Tweeter as a K77 is good. Its even rebuild able now with new diaphragms should you need, but as I have access to Fastlane audio's elliptical tweeter... why not use a modern bad *** tweeter instead. Fastlane's tweeter lens is $100 for pair. The B&C DE10 or DE120 are my choices and are fantastic. I might go with Eminence ASD1001B as its American made and a solid performer too. I measured the drivers and got to selling all the parts I would not use on eBay. The Mid horns were the usable but not my cup, K701 with the bold on K53. (No one wants a K53/K701 combo). It got sold off for $100 to a local buyer who had his own project. I was able to purchase a K700/K55 push pin style (My preference on the K55) for $180 to my door. Normally this would be $200-$240 but I got a good deal. This will now make the Heresy a OG classic which has been upgraded. Same looking horn, but metal instead of ABS and Screw on instead of bolt on. (You can roll drivers if you wanted to now.). The cabs were less than ideal. Klipsch builds with 3/4" ply and 1/2" ply for he back panel. We laminated 1/4" to all the sides of the speaker... giving us a new corner edge and a stiffer cabinet. The front and back are edge banded to hide the lamination. The inside of the back panel had 1/4 MDF added. This will provide a key to center the back panel and panel increased surface area when its inset inside the cabinet... Long story short, its a hair smaller now but a ton stiffer. Additionally I love the look of slant risers on the Heresy. I went to Bob writes and ordered a set. Ebay sales: K77 Tweeters sold for $90 E2 Crossovers sold for $50 K22 Woofers sold for $80 New parts: ALK CSW700 crossover $350 Eminence 12LFA $130 Fastlane audio Tweeter Lens $100 Eminence ASD1001B $50 pair K700/K55 $180 Wood Work $200 for extra ply/finishing costs $40 for the slant risers ____________________________ $810 $240 -$220 Total: $830 Im into the whole speaker for ~$1250. Its a lot of money for sure, but there is no way it would sound remotely as good. Work has just started but I wanted to show the starting point, and plan. Here are the before pics.