Search the Community
Showing results for tags 'buyers guide'.
Found 1 result
Note (24 April 2021): This thread has been overcome by events (OBE). I do not currently recommend spending much time in this thread (created by myself), as the supply of the loudspeakers found here has been discontinued by Klipsch. I have elected to leave the information in this thread intact for the benefit of those looking to buy used models of the Klipsch Professional version (two-way) for home hi-fi use. The information here may be useful to those individuals, but there are apparently no "new" Jubilees of the version discussed here that are being manufactured by Klipsch, and those holding stock quantities of these loudspeakers have apparently sharply increased their prices of late. This is unfortunate, but as they say, "all good things must pass", seems to apply in this case. Please PM me if you have any questions. _____________________________________________________________ _____________________________________________________________ Some frequently-asked potential buyer questions (FAQs) for the home version Klipsch Jubilee: 1) What is a Jubilee? The Klipsch Jubilee consists of a redesigned dual-mouth ("W" section) bass bin having horn expansion path in one axis (versus both the horizontal and vertical in the original Khorn bass bin), and the K-402 high frequency horn on top that uses a full-range 2" compression driver, thus bringing the Klipschorn design back to its original two-way design of the 1940s and '50s that its inventor wished it to be. The crossover point is nominally 450-500 Hz. As sold by Klipsch, the two-way home version Jubilee was intended to be bi-amped using a DSP crossover, i.e., a "loudspeaker processor", for crossover and EQ balancing--the thin dark gray box on top of preamplifier in the photo below is one DSP crossover that is used with the Klipsch Jubilee. Third party passive crossovers are not supported by Klipsch, although there are passive schematics for the K-69-A compression driver and TAD TD-4002 compression driver (both drivers now discontinued). 2) What's so special about the Jubilee? Why should I consider buying them? The Klipsch Jubilee was originally developed to be the replacement for the Klipschorn (corner horn). Paul Klipsch intended to call it a "Klipschorn II", but its performance so exceeded the expectations of its inventor that the decision was made to call it the "Jubilee" in commemoration of the 50th year of the Klipschorn introduction to the marketplace in the mid-late 1940s. The Klipschorn is the only known loudspeaker to be in continuous production for all of those 50 years. Many that have heard Klipsch Jubilees consider them to be the finest loudspeaker that Klipsch produces. If you hear them, you'll understand why. The advantages of the Jubilee design over the original Klipschorn are: time alignment of the entire loudspeaker, leading to more neutral sounding loudspeakers overall without crossover interference band-induced timbre changes much better directivity vs. frequency of its acoustic output, leading to a huge soundstage image and very smooth sounding performance overall higher efficiency of both the bass bin and hf horn/driver due to the elimination of the passive crossover extremely low reactance load--direct connect to drivers to maximize driver damping much better frequency response flatness using the built-in equalizing filters in the DSP crossover to correct for the controlled directivity K-402 horn/driver and room response variances, especially in the midbass and below frequency bands Some history of the Klipsch Jubilee design, its bass bin, and K-402 horn can also be found here: 3) How much does a Klipsch Jubilee cost? The two-way Jubilees cost somewhat less than new Klipschorns. 4) What product ordering options are available? Klipsch provides a bass bin front panel veneer in a number of veneer choices. The K-691 compression driver (rebranded B&C DE75) is the standard driver bundled with the two-way home version Jubilee. 5) Where can I hear a pair of Jubilees? See the following thread: 6) Where can I buy a Jubilee? The two-way (home hi-fi version) Jubilee can be ordered in the U.S. through @MetropolisLakeOutfitters --a Klipsch dealer. Other dealers can be found through contacting Roy Delgado (email@example.com). 7) Does Klipsch provide setup support? If not, where can I get help? Klipsch does not provide setup support for these loudspeakers. Additional help can be obtained through Jubilee owners here on the Klipsch Forum. Free help with getting them dialed-in using DSP crossover can be obtained through @Chris A via email support using Room EQ Wizard (REW) and your chosen DSP crossover. It is recommended that you first consider using a Xilica crossover (XP or XD series) to facilitate the dialing-in tasks, although other DSP crossover types can also be used. It is also recommended that you use a better quality DSP crossover than a miniDSP, Behringer, and the entry-level dbx Driverack. 8 ) What active crossovers are used? What's recommended ? How do I program it? Several types of DSP crossovers have been used with the two-way home version Jubilee, including the older ElectroVoice Dx38 and its successor DC-One, Yamaha SP2060, Ashly Protea, Xilica XP series, and miniDSP 2x4 HD. If buying through MetropolisLakeOutfitters, preloading of Xilica XP processor settings developed by Roy Delgado of Klipsch is an option supported by the dealer. 9) How do I buy a Jubilee if I don't live in the U.S.? What are my options? Contact Roy Delgado (firstname.lastname@example.org) to discuss your options for international sales. Note that most Klipsch dealers do not often handle Klipsch Professional products (i.e., cinema). Based on the history of difficulties getting the correct configuration for two-way home hi-fi operation, it is recommended to email Roy Delgado before contacting your local Klipsch dealer if you do not live and ship to the U.S. Chris