Jump to content

Search the Community

Showing results for tags 'refinishing'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Klipsch Announcements
    • Klipsch News
    • Klipsch Pilgrimage 2020
    • Klipsch Website & Forum Info
  • Klipsch Museum of Audio History
    • Klipsch Museum: News & Announcements
    • Ask the Historian
    • Klipsch Museum: General Discussion
  • Klipsch Audio
    • General Klipsch Info
    • 2-Channel Home Audio
    • Home Theater
    • Subwoofers
    • Architectural
    • Klipsch Pro Audio
    • Technical/Modifications
    • Headphones
    • Personal Music Systems
    • Talkin' Tubes
    • Solid State
  • The Klipsch Joint
    • Garage Sale
    • Lounge

Calendars

There are no results to display.


Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


Location


Interests


My System


See My System


Website URL


Twitter


Skype


AIM


Yahoo


MSN


ICQ


Jabber

Found 4 results

  1. I recently acquired a pair of 1986 Lascalas. The raw birch cabinets had some damage (chips, delamination, chewed-off corner) that I have mostly repaired. I’m now about to strip the existing polyurethane and refinish them. I’ve spent a lot of time on this site and the web (e.g., Volti site) trying to ascertain how best to proceed. I was thinking about laminating a ¼” Baltic birch panel to the sides, top, and bottom (but not the front or the back) and then applying veneer on the top, bottom, sides and front (but not the back). 1) Will adding the ¼” panels hurt the value of the speakers? If so, I’ll likely not add them. Adding the ¼” panels would increase the rigidity of the cabinets and provide a smooth surface for the veneer. I’ll use Tite-Bond (PVA glue) to laminate the ¼” panels to the cabinets. Although I have some clamps, I’ll rely on weights and some pin nails to hold the panels while the glue dries. 2) I’d welcome any suggestions about better ways to laminate the panels to the cabinets. I’ll be using sheets of paper-backed veneer. I’m concerned about how best to apply the veneer, specifically how to avoid bubbles/poor adhesion when applying it and chip-out/tearing when trimming it. I’ve been thinking of cutting the veneer slightly oversize, gluing it to the cabinet with contact cement, and then using a flush-trim bit in a router to cut it to size. Alternatively, I could glue the veneer to the ¼” panels before installing them and then install the veneered panels (using Tite-Bond, pin nails, and weight) but I’d still have to use the former approach for the front of the cabinets. 3) I’d welcome advice about how best to apply the veneer, especially from those that have “been there and done that”. I’m scouring this site and the web looking for images of Lascalas to help choose a type of veneer and finish for the speakers. 4) I’d appreciate seeing images of Lascalas that might help me choose the veneer and finish for the speakers. 5) What have people done with the exposed end-grain on the cut-outs for the tweeter and sqawker (see photo)? Those curved surfaces would be tricky to veneer so I'm thinking of just painting them a flat or satin black. I have other questions pertaining to how to finish the bins. I’ll post those in another message. Thank-you. Dave MacKay near Toronto, Canada
  2. Hey y’all! I’ve had the fives for about 6 months or so and something about the natural oak just doesn’t look the best to me. I’d like to refinish these with a darker stain, but I just don’t know how to go about it. I know that refinishing veneer is challenging and I also don’t know how thin the veneer is on these. I know this isn’t that big of a deal, but if anyone has any advice I’d love to hear it. Thanks!
  3. I am in love with these La Scalas and would like to found out "how they did it" finiis, veneer (oak?), grill support and all the other details. This is the look I am after for my really beat up 1976 La Scalas. Thanks to all.
  4. Been enjoying my La scalas. They are a bit stained/dirty? I tried the beeswax/orange paste wipe on wipe off and didnt really notice a difference. Do i need to sand/buff and then what to seal it? They are raw birch and i love that look so want to keep that look and not stain/color/tint them..... Any advice???
×
×
  • Create New...