Jump to content


Photo
- - - - -

KP-250 pole mount size?


  • Please log in to reply
6 replies to this topic

#1 jwc

jwc

    Klipsch Fanatic

  • Members
  • PipPipPipPipPipPip
  • 5,002 posts
  • Offline

Posted 14 December 2013 - 01:13 PM

Probably a dumb question.....anyone have the PDF on this?

1 1/2 or 1 3/8?



#2 Pete H

Pete H

    Forum Veteran

  • Members
  • PipPipPipPip
  • 1,676 posts
  • Offline

Posted 14 December 2013 - 01:19 PM

I can check the bars when I get home but don't have a PDF


Pete ........It is what it is! Onkyo 805 and 890, Sansui 8080 and G5500, Sony STRDE997, Carver CT7, 5 Carver M200's, Oppo 983, Sony S7000, S7700, S9000, Behringer 16 Channel Mixer and DCX 2496, QSC DCA1622, RF 7's, RC7,RS7's, RSW15's, RF35's, RP5's and 8's, RC3's, RB5's, RB61's, Cornwall 2's, Split Cornscala's, Velodyne1512

#3 jwc

jwc

    Klipsch Fanatic

  • Members
  • PipPipPipPipPipPip
  • 5,002 posts
  • Offline

Posted 14 December 2013 - 01:27 PM

I bought the 1 1/2.....but it seems I would have to tap with a hammer to get in there. I'm embarrassed but.....I never used the poles on any of my past setups :unsure2:



#4 Pete H

Pete H

    Forum Veteran

  • Members
  • PipPipPipPip
  • 1,676 posts
  • Offline

Posted 14 December 2013 - 01:34 PM

I don't have to tap them to get them in.


Pete ........It is what it is! Onkyo 805 and 890, Sansui 8080 and G5500, Sony STRDE997, Carver CT7, 5 Carver M200's, Oppo 983, Sony S7000, S7700, S9000, Behringer 16 Channel Mixer and DCX 2496, QSC DCA1622, RF 7's, RC7,RS7's, RSW15's, RF35's, RP5's and 8's, RC3's, RB5's, RB61's, Cornwall 2's, Split Cornscala's, Velodyne1512

#5 Pete H

Pete H

    Forum Veteran

  • Members
  • PipPipPipPip
  • 1,676 posts
  • Offline

Posted 17 December 2013 - 08:23 PM

Really measures about 1 7/16 so 3/8 is probably going to be a bit sloppy so better a little tight.
Pete ........It is what it is! Onkyo 805 and 890, Sansui 8080 and G5500, Sony STRDE997, Carver CT7, 5 Carver M200's, Oppo 983, Sony S7000, S7700, S9000, Behringer 16 Channel Mixer and DCX 2496, QSC DCA1622, RF 7's, RC7,RS7's, RSW15's, RF35's, RP5's and 8's, RC3's, RB5's, RB61's, Cornwall 2's, Split Cornscala's, Velodyne1512

#6 djk

djk

    Klipsch Fanatic

  • Members
  • PipPipPipPipPipPip
  • 5,260 posts
  • Online

Posted 17 December 2013 - 09:26 PM

Use 1-3/8", the amount of slop is only ±1/32", a 1-1/2" pole will not fit properly. You could wrap the 1-3/8" pole with a layer of duct tape if you want it too tight.


Golden Ear Audiophile hit with a brick "Oww, that hurts! I'm bleeding!" Tin Ear Meter Reader hit with a brick "You can't prove I was hit with a brick! We need to do a double blind ABX test!"

#7 jwc

jwc

    Klipsch Fanatic

  • Members
  • PipPipPipPipPipPip
  • 5,002 posts
  • Offline

Posted 22 December 2013 - 11:57 AM

Thx. I screwed up and got the wrong size