Invidiosulus 12 Posted October 30, 2018 Next I measured the angle between the two faces with a sliding bevel gauge. Verified the correct angle (31.6 degrees). This matches up nicely with the front piece at the correct angle with 125 degrees between them in the horizontal plane. Cheers, Josh Quote Share this post Link to post Share on other sites
planetred 28 Posted October 30, 2018 Getting the "wishbone" just right is a little tricky. When you dry fit it in the box with the motor board on top, it all comes together. Good luck! 1 Quote Share this post Link to post Share on other sites
Edgar 1041 Posted October 30, 2018 Referring to pieces 2, 3, and 4 in the original University drawing; wouldn't it be easier to make them all perpendicular to the base piece 5, and then add a solid wedge reflector at the correct angle? That's how Klipsch does it, except that Klipsch splits the path two ways instead of just one. Quote Share this post Link to post Share on other sites
Marvel 5597 Posted October 30, 2018 5 hours ago, Edgar said: Referring to pieces 2, 3, and 4 in the original University drawing; wouldn't it be easier to make them all perpendicular to the base piece 5, and then add a solid wedge reflector at the correct angle? That's how Klipsch does it, except that Klipsch splits the path two ways instead of just one. Parts 3 and 4 are perpendicular to the base already. Part 2 slants toward the front. If you make them all vertical, then you will have to cut angles on the sold wedge, or not worry too much and caulk where you didn't make it fit. Once these angles are known, it will be easier to make. I was also getting confused with the two side pieces and getting the compound angle correct, but it looks like Josh has it figured out. (one of the newer sets of plans from University has all the edges mitered for the throat, which must have been a bear to cut and get together. Quote Share this post Link to post Share on other sites
ajsons 19 Posted October 30, 2018 On 10/30/2018 at 9:15 AM, planetred said: Quote Share this post Link to post Share on other sites
ajsons 19 Posted October 30, 2018 1 hour ago, Marvel said: I was also getting confused with the two side pieces and getting the compound angle correct, but it looks like Josh has it figured out. (one of the newer sets of plans from University has all the edges mitered for the throat, which must have been a bear to cut and get together. There you go, Bruce. Time to see some sawdust. Quote Share this post Link to post Share on other sites
Marvel 5597 Posted October 31, 2018 20 hours ago, carlthess40 said: Hi I’m near I:4 and Lake Mary blvd I’ve only look at the plans in bits so far and have no way to know of how much labor will be in to one yet @carlthess40 Just north of Orlando? Cool Quote Share this post Link to post Share on other sites
carlthess40 594 Posted October 31, 2018 Yes sir Quote Share this post Link to post Share on other sites
Marvel 5597 Posted October 31, 2018 On 10/29/2018 at 3:22 PM, Invidiosulus said: I believe the relative angles for the boards can be checked using a compound angle calculator such as this one. http://jansson.us/jcompound.html Very, very cool tools on this page... Quote Share this post Link to post Share on other sites
ajsons 19 Posted October 31, 2018 Really cool. Maybe I'll check those out during recovery. Quote Share this post Link to post Share on other sites
planetred 28 Posted October 31, 2018 I remember seeing Nico's Classics and wondered how much it changed the resonance of the box. Very interesting take on the Classic though. https://community.klipsch.com/index.php?/topic/146927-the-rebirth-of-the-university-classics/ Quote Share this post Link to post Share on other sites
gazzamongo 5 Posted October 31, 2018 Amazing thread. Had been curious about this cabinet for a while so I'm super grateful for ajsons and the other contributor's for demistifying those sketchy old plans. Although I'm sure twin evm12ls would be pretty spectacular, that runs me about £1000.00 in the u.k.Any other driver recommendations? Wondering if the eminence kappa 15c that Claude recommends for his quarter pie is suitable *Or for a few dollars more -> http://www.precision-devices.com/Product-Details/PD153ER ? Thanks (* That's another cab I'm wanting to try out if it'll fit well enough in my small room )Sent from my Lenovo TAB 2 A10-70F using Tapatalk Quote Share this post Link to post Share on other sites
planetred 28 Posted October 31, 2018 The c15w has a flat smooth voice. Nothing sounds quite like it. My friend and I tried an eminence in his classic, delta pro15a, but it had too much voice. Wish I could help you further. 1 Quote Share this post Link to post Share on other sites