Marvel Posted June 28, 2019 Share Posted June 28, 2019 That's the plate rating for that particular tube. Same as the new Western Electric 300B tube. I certanly don't know what the expected power output can be. Bruce Quote Link to comment Share on other sites More sharing options...
codewritinfool Posted June 28, 2019 Share Posted June 28, 2019 That's the plate rating for that particular tube. Same as the new Western Electric 300B tube. I certanly don't know what the expected power output can be. Bruce Around 3.5W for a 2A3. Around 8W for a 300B. Quote Link to comment Share on other sites More sharing options...
Marvel Posted June 28, 2019 Share Posted June 28, 2019 2 hours ago, codewritinfool said: Around 3.5W for a 2A3. Around 8W for a 300B This is correct, just pointing out the plate dissipation rating for the JJ 2A3 40 tube is 40Watts. https://www.tubedepot.com/products/jj-2a3-40-watt-power-vacuum-tube The new WE 300B has the same maximum plate dissipation. https://www.google.com/search?q=new+western+electric+300B+spec+sheet If you run the 300B at near maximum, you can get approx. 17 watts out. 1 Quote Link to comment Share on other sites More sharing options...
Marvel Posted June 28, 2019 Share Posted June 28, 2019 I wouldn't want to waste a new WE 300B by doing that, though. Not at $1500 a pop... 😟 Quote Link to comment Share on other sites More sharing options...
moray james Posted June 28, 2019 Share Posted June 28, 2019 I agree that listening to a single channel (use the same channel for both amplifiers) to listen and evaluate is a good idea as listening to stereo can be confusing, you can get lost listening to stereo effects and not the hear as easily the balance of the amp under test. Choose a mono recording or if you don't have one a single channel of a tune in stereo that you know well which has a good wide range of information/instruments on it. This also results in eliminating half of your room interactions present in a stereo listening set up so that will help to make it easier for you to hear what each amp is doing. 1 Quote Link to comment Share on other sites More sharing options...
DjOverdose Posted June 28, 2019 Author Share Posted June 28, 2019 6 hours ago, Schu said: He's expecting 40w out of a 2a3? nope... thats the model of the power tubes. Quote Link to comment Share on other sites More sharing options...
DjOverdose Posted June 28, 2019 Author Share Posted June 28, 2019 1 hour ago, Jeffrey D. Medwin said: I'd suggest, forget a 300B, avoid unnecessary toggle switches, and amplifiers needing adjustments. KISS rules !! . The 300B requires a DC filament operation, due to its 5 V filament requirement. Have your amp built using ONLY JJ 2A3-40s, which is a SINGLE 40 Watt ( 300B ) plate tube, with a symmetrical harp-like cathode, and a 2.5 VAC filament requirement, so you can employ AC heating, which sounds better !! The JJ 2A3-40, properly employed, just totally destroys every Type 45 tube amp I have built and heard, on my system, but I have not heard a solid plate EML. ( The solid plate EML $$$$$$ also has a symmetrical harp-like cathode and advantageously, a single plate ) and its made in the same Prague Factory as a $130 JJ 2A3-40 !! Be sure to use good wiring, in the amp, and all the way to the Klipsch Drivers' speaker terminals / and / or to the Drivers' voice coil terminals. I did this, this last year, with a 0.25 Watt triode amp, and it has made a world of difference. Never operate tube plates near maximum ratings, first of all, they SOUND worse - thermally stressed that way, and their useful life is drastically reduced. Jeffrey hey jeff. thanks for the input. i have no ideawhat wires his using inside the amp. im using a QED XT silver anniv as my speaker wire. i wonder what the speaker will sound like and using a copper one. i cant do anything About the toggle switch since it was alrradu6 thetr. Quote Link to comment Share on other sites More sharing options...
Marvel Posted July 1, 2019 Share Posted July 1, 2019 On 6/28/2019 at 10:37 AM, Jeffrey D. Medwin said: The 300B requires a DC filament operation, due to its 5 V filament requirement. My 2A3s have a 5 volt filament and don't require dc. The amps would be quieter if I did, though. Quote Link to comment Share on other sites More sharing options...
garyrc Posted July 1, 2019 Share Posted July 1, 2019 On 5/28/2019 at 7:54 AM, DjOverdose said: i only have a small space for the speakers though. ive read somewhere that the reference are not that sensitive as advertised. How small is small, in cu.ft.? How far away do you sit? How loud do you like it, in dB, on loud passages? Is your room live, medium, or dead? Klipsch's sensitivity ratings are true in an average room with typical room and boundary gain (i.e., not out in the middle of the room, but very near a solid wall, or in a corner). To convert to an anechoic rating, subtract 4 dB from the published rating; at least that's what a Klipsch employee said on the forum (about a year ago?). Inside, in a room (forget about outside) each doubling of distance will cost you about 3 dB or so (not 6 dB!) this was a figure arrived at by PWK. It is literally true (on the nose!) in my room. So, if the RP 280Fs are against (or almost against) a wall, that would give you 98 dB at 1M at 1W, 95 dB at 2 M at 1W, and 92 dB at 4 M (about 13 feet) at 1W ... going back up, at 2 watts, we would have 95 dB/2W/at 13 feet. That's enough for some people, but not others. Klipsch considers that to be at the "loud" but not "very loud" level (Don Keele Jr., Dope from Hope V16, no1, January 1977). As long as everything (all amplification) is working correctly, you would still get 1.5 watts more headroom. Someone else may be able to tell you whether the RP 280F has any impedance anomalies that would be a problem. I have noticed that some Klipsch speakers sound better with more power than they need, but there were covariates I didn't know how to account for. Quote Link to comment Share on other sites More sharing options...
Marvel Posted July 1, 2019 Share Posted July 1, 2019 12 hours ago, Jeffrey D. Medwin said: Thats highly unusual. That is because I was mistaken. It is 2.5 volts. mea culpa, mea culpa! Quote Link to comment Share on other sites More sharing options...
DjOverdose Posted July 2, 2019 Author Share Posted July 2, 2019 On 7/1/2019 at 3:21 PM, garyrc said: How small is small, in cu.ft.? How far away do you sit? How loud do you like it, in dB, on loud passages? Is your room live, medium, or dead? Klipsch's sensitivity ratings are true in an average room with typical room and boundary gain (i.e., not out in the middle of the room, but very near a solid wall, or in a corner). To convert to an anechoic rating, subtract 4 dB from the published rating; at least that's what a Klipsch employee said on the forum (about a year ago?). Inside, in a room (forget about outside) each doubling of distance will cost you about 3 dB or so (not 6 dB!) this was a figure arrived at by PWK. It is literally true (on the nose!) in my room. So, if the RP 280Fs are against (or almost against) a wall, that would give you 98 dB at 1M at 1W, 95 dB at 2 M at 1W, and 92 dB at 4 M (about 13 feet) at 1W ... going back up, at 2 watts, we would have 95 dB/2W/at 13 feet. That's enough for some people, but not others. Klipsch considers that to be at the "loud" but not "very loud" level (Don Keele Jr., Dope from Hope V16, no1, January 1977). As long as everything (all amplification) is working correctly, you would still get 1.5 watts more headroom. Someone else may be able to tell you whether the RP 280F has any impedance anomalies that would be a problem. I have noticed that some Klipsch speakers sound better with more power than they need, but there were covariates I didn't know how to account for. Hi Garyrc! i really dont know the exact size of the area. its a mix used room though, dinning, living room etc. i listen probably around 2M away from the speakers. Due to the limited space i have, my speakers are almost close to the wall. after reading your reply, I guess the 2A3 amp will be fine on powering the RP280f. hopefully My amp will be finished this week 2 Quote Link to comment Share on other sites More sharing options...
DjOverdose Posted July 7, 2019 Author Share Posted July 7, 2019 On 6/28/2019 at 6:01 PM, Schu said: He's expecting 40w out of a 2a3? nope... thats the model of the tubes. JJ 2a3 40W Quote Link to comment Share on other sites More sharing options...
DjOverdose Posted July 7, 2019 Author Share Posted July 7, 2019 almost done. just waiting for the cage to be finished. the builder say its somewhere around 3.5WPC to 4WPC. 1 Quote Link to comment Share on other sites More sharing options...
Schu Posted July 7, 2019 Share Posted July 7, 2019 I bet you can't wait to hear it fire up for the first time... you're going to be impressed and happy. Quote Link to comment Share on other sites More sharing options...
Backfire Posted July 7, 2019 Share Posted July 7, 2019 That looks really nice! Very nicely built. Quote Link to comment Share on other sites More sharing options...
Moderators Travis In Austin Posted July 9, 2019 Moderators Share Posted July 9, 2019 On 7/7/2019 at 8:24 AM, Jeffrey D. Medwin said: The rectifier tube should located be as FAR away as possible, from the input tubes. Here, we see just the opposite, close-to and smack dab between both of the input tubes. Dude, please back off on being critical of everything and anything that doesn't fit your ideal design parameters. If you see something you just can't contain yourself about, i.e. please start a new thread in Talkin' Tubes about the relative pros and cons of locating a rectifier in between two input tubes. You can do the post without referencing any particular persons equipment they are building, or purchasing, or whatever. When you do make such posts it would be helpful if you included a source besides your 40+ years of building experience as many on here have that, or what your ears tell you, as everyone has those along with a personal preference to go along with it. Thank you. 3 Quote Link to comment Share on other sites More sharing options...
Moderators Travis In Austin Posted July 9, 2019 Moderators Share Posted July 9, 2019 On 6/28/2019 at 9:11 AM, Marvel said: I wouldn't want to waste a new WE 300B by doing that, though. Not at $1500 a pop... 😟 I thought they were half price for locals. Made you look😝 Quote Link to comment Share on other sites More sharing options...
Moderators Travis In Austin Posted July 9, 2019 Moderators Share Posted July 9, 2019 On 5/28/2019 at 7:59 AM, moray james said: don't count on the published efficiency levels being accurate, you can expect them to be in the range of at least 2 - 3db hot and they are often measured at 1KHz.. Still a 2A3 can surprise most audiophiles, I am sure yours will also. It is sensitivity, not efficiency. It would depend how he has them placed in his room, and his room, on whether they will be right at spec, below, or even above, right? 1 Quote Link to comment Share on other sites More sharing options...
Moderators Travis In Austin Posted July 9, 2019 Moderators Share Posted July 9, 2019 On 6/28/2019 at 11:12 AM, Jeffrey D. Medwin said: If you have a good stereo amp design, simply listen to just ONE channel, playing one speaker, and decide for YOURSELF. I find that the local builder told you wrong. I have often made the same mistake !! There really is no comparison to what monoblocks do, after you do the above mentioned test I suggested. My 2019 KT88 will become the LAST stereo amp I EVER build for myself. Jeffrey He said the cost difference didn't justify the added expense to HIM. Simply say, all things being equal, you prefer monoblocks. You don't know that his builder told him something "wrong." He told him something you have a difference of opinion on. Please keep this a nice friendly place, the one Maynard envisioned when he requested it be created Thanks 2 1 Quote Link to comment Share on other sites More sharing options...
Moderators Travis In Austin Posted July 9, 2019 Moderators Share Posted July 9, 2019 On 7/7/2019 at 12:47 AM, DjOverdose said: almost done. just waiting for the cage to be finished. the builder say its somewhere around 3.5WPC to 4WPC. That's some Mang, good for you. So does that amp give you the option to go 300b, 45 like the one you described at the beginning of your thread? If so you are going to be able to try a lot 9f every cool things! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.