Jump to content
The Klipsch Audio Community
Sign in to follow this  

KP-362 low end advice

Recommended Posts

hello gents- if you want to skip the bs just go down a couple paragraphs. but right up front i must say i've been lurking a bit around here since the events i'm about to tell you about and i do believe i could get along with the lot of you in an outdoor type setting. since this is my first post i will admit that for most of my life i was under the impression klipsch made some decent bookshelf speakers. then one of the kp-362s that was, not really flown but just kind of resting up high on some 2x4s above the bathroom at the gym, vibrated its way right off there and luckily did not bonk anybody on the way down. the owners luck also became my luck, as i was permitted to take possession of the lightly dinged boxes along with a gem sound 200W amp. i know i'm not the only one that likes analog meters.


for the longest time i had one 362 set up for parties in my kitchen. i grew to really like the sound and wonder if i'll like it even more when i replace the hf driver. so i recently had the opportunity to reimagine my hobby area (living room) and have put the pair to work. i've been doing my version of "tuning" (some would just call it setup) and i've come across a couple of issues that i think this board is where i'd like to find my answers.



as you can see in the picture, my current configuration is a stack in the corner of the room with the kp-362 packed side by side running LF + mid, then perched up top is a yorkville nx550p - full range active 12" with lows rolled off at 100.


the problem is i can't get the really low end i'm after from the klipsch. i can get it when i turn up and send a 25Hz tone, but obviously that doesn't work for program material. i haven't been able to locate the detailed specs on these but i assume the low rolls off at 60 as with the ki-362. 


so like i said i can hear the speakers are capable of those supersubby tones. does anyone have advice on how to get that happening or is there no way to win this without a sub? is there a another driver i could substitute that extends lower? (fwiw this will not be running anywhere close to full volume.) i have a 30 band rane eq sitting here waiting for a power supply, could that help? and if i do need a sub, please tell me there is something other than the ki-215. of course i want this to sound good but that's too much to just have in my living room.


feel free to give me untested, caveated, or generally-considered-poor advice. 


the other question is: i found a link on here to a guy on ebay who sells replacement HF drivers. is this what i want? 


here are some answers to things some people might wonder about.

- i'm planning to replace the 200W gem sound with a peavey cs800.

- i'm using the yorkville because i like oddball setups and i haven't replaced the HF drivers in the 362s. 

- after reading about how line arrays work, i had put the 362s side by side with the intent - and to see if i could observe - the phenomenon of acoustic coupling of the LF drivers. 

- i'm running mono because i like it that way. i put sound in other places by sending to a small collection of guitar amps and rando transducers.


i look forward to hearing from some of you folk.






Edited by futurefunk@gmail.com

Share this post

Link to post
Share on other sites

Yes those tweeters are the ones you want.


As far as bass goes  sky is the limit really if you're looking for something new and reasonably priced the Klipsch r-115sw gets good reviews and go on sale often for nearly half price.

  • Like 1

Share this post

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Create New...