justinsweber Posted July 13, 2020 Share Posted July 13, 2020 Upgrading to the separates. No scratches. Flawless condition.... need to whipe my finger prints off the front 🙂  The Hint has been an incredibly good integrated for me... 1 year old. Only used to drive my Cornscalas. $1600  Shipped. Justin 949-636-9076  Parasound HINT 6 New Features Burr Brown analog resistor ladder volume control Dimmable front panel volume display Updated USB receiver is plug-and-play with Windows 10 and Mac An additional optical input (2 total) Ball bearing supported solid aluminum volume knob Programable default turn on volume setting Favorite volume memory with remote control button Increased phono stage gain for lower output cartridges Improved Left/Right channel separation and balance tracking Updated cosmetics with subtle gold highlights Parasound HINT 6 Preamplifier Features ESS Sabre32 Reference DAC (ES9018K2M) Asynchronous USB 2.0 supports PCM up to 384kHz/32-bit USB input decodes Native DSD64, DSD128, DSD256 and DoP DSD Coax and optical inputs accept PCM up to 192kHz/24-bit Analog bass management with high & low pass crossovers Home theater bypass input for surround sound integration Front panel subwoofer level control Dedicated high current headphone amplifier (TI TPA6120) Phono input for MM, MC and MI with 100 ohm or 47 kohm load Front panel Aux input with automatic +12 dB gain stage 5 pairs RCA line level Analog inputs 1 pair XLR balanced Analog input Balanced XLR and RCA left and right preamp outputs 1 balanced XLR and 2 RCA subwoofer outputs Bass and treble controls with relay bypass from remote or front panel Rear panel IR input and IR loop output jacks 12 Volt trigger output Back-lit remote control with discrete buttons 0.5w standby power consumption meets Energy Star & EU specs Parasound HINT 6 Power Amplifier Features 160 Watts x 2 @ 8 Ohms (RMS, both channels driven) 240 Watts x 2 @ 4 Ohms (RMS, both channels driven) Power amp circuit topology designed by the legendary John Curl Direct amplifier input to bypass preamp section High bias class A/AB operation Oversized shielded toroid power transformer Dual-mono power supply and power amplifier 40,000uF power supply filter capacitance Matched JFET input stages and MOSFET driver stages 12 high voltage/high current bipolar output transistors Heavy-duty 24k gold-plated 5-way speaker binding posts Over temp and short circuit relay protection  Power Output - Both channels driven (0.05% THD, RMS, 20Hz - 20kHz): 160 watts x 2 @ 8 ohms; 240 watts x 2 @ 4 ohms Power Output - Both channels driven (0.9% THD, RMS, 20Hz - 20kHz): 180 watts x 2 @ 8 ohms; 270 watts x 2 @ 4 ohms Current Capacity: 45 amps peak per channel Frequency Response: 10Hz - 100kHz, +0/-3dB; 20hz-20kHz, +0/-0.5 dB Total Harmonic Distortion (THD): 0.01 %, average listening levels; < 0.05 %, 160 watts x 2 @ 8 ohms Interchannel Crosstalk: > 70dB at 20kHz; > 78dB at 1kHz Signal to Noise Ratio - IHF A-weighted: Line in: - 103dB (input shorted); Digital in: - 106dB Amplifier Damping Factor: 800 at 20Hz Preamp Stage Input Sensitivity: 300mV in for 1V at Pre Out jacks; Total Preamp Stage Gain: 10dB; Max Output Unbalanced: 7 V; Max Output Balanced: 9 V Power Amplifier Stage Sensitivity: 1V at Bypass/Amp In for 28 V at Speaker Out; Total Amp Stage Gain: 28dB Phono Stage Sensitivity / Input Impedance: MM 41dB / 47kohms; MC 54dB / 47kohms or 100 ohms High and Low Pass Crossover Slopes: 12dB per octave Supported DAC Sampling Rates: USB: up to 384kHz / 32-bit PCM; DSD Native: DSD64, DSD128, DSD256; DSD over PCM (DoP) at 384kHz; Coax/Optical: up to 192 kHz / 24-bit PCM; Digital to Analog Converter: ESS Sabre32 Reference ES9018K2M; 384kHz / 32-bit USB 2.0 Controller: Savitech SA9227, 384kHz / 32-bit Headphone Amplifier: Texas Instruments TPA6120A; Output Impedance: 10 ohms Input Impedance: Unbalanced: 24kohms: Balanced: 100kohms per leg Preamplifier Output Impedance: Unbalanced: 100 ohms; Balanced: 470 ohms per leg Power Requirements: Standby: 0.5 watts; Idling power: 70 watts; Maximum: 750 watts; 110-125 VAC 60Hz or 220-250 VAC 50Hz; AC mains voltage is set on rear panel Dimensions: 17-1/4" wide, 16-1/4" deep (with cables 17-1/4"), 5-7/8" high with feet (without feet 5-1/4") Weight: 33 lb.   Quote Link to comment Share on other sites More sharing options...
314carpenter Posted July 15, 2020 Share Posted July 15, 2020 Fantastic product. Great price. GLWYS. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.