luddite Posted December 8, 2020 Share Posted December 8, 2020 I have acquired a SX 1250 in original condition. I thought it would need just a good clean up, but closer inspection reveals more. There is surface corrosion on the jacks at the rear of the unit, and what I hope is just surface rust (or pitting) on the chassis. The shaft for the balance knob has a slight bend. The unit was stored for an extended period, and it shows. The good news is that it is fully functional, and works as it should. I would like to have it restored to as new condition. I have seen listings on eBay for "restoration services", but have no knowledge of who is reputable. Anybody have a good Pioneer repair/restoration resource? I am willing, and expect to have to ship it. I'd like to keep the amp for a while. 1 Quote Link to comment Share on other sites More sharing options...
OO1 Posted December 8, 2020 Share Posted December 8, 2020 I would not ship it , the knobs and controls can bend , the unit would be subjected to a lot of manipulation , and some of these parts cannot be replaced Quote Link to comment Share on other sites More sharing options...
jimjimbo Posted December 8, 2020 Share Posted December 8, 2020 13 minutes ago, luddite said: I have acquired a SX 1250 in original condition. I thought it would need just a good clean up, but closer inspection reveals more. There is surface corrosion on the jacks at the rear of the unit, and what I hope is just surface rust (or pitting) on the chassis. The shaft for the balance knob has a slight bend. The unit was stored for an extended period, and it shows. The good news is that it is fully functional, and works as it should. I would like to have it restored to as new condition. I have seen listings on eBay for "restoration services", but have no knowledge of who is reputable. Anybody have a good Pioneer repair/restoration resource? I am willing, and expect to have to ship it. I'd like to keep the amp for a while. Location? Quote Link to comment Share on other sites More sharing options...
luddite Posted December 8, 2020 Author Share Posted December 8, 2020 I'm in Memphis. And, I've shipped many pieces, including Mac units with the fragile glass fronts, without issue. I'm not afraid to send the reciever off to a good repairman. It will be well packed; I would like the restoration to be the same. I do have a couple of places locally I use for repairs, but would not trust them to make the receiver as new. Quote Link to comment Share on other sites More sharing options...
OO1 Posted December 8, 2020 Share Posted December 8, 2020 On 12/7/2020 at 10:47 PM, luddite said: I do have a couple of places locally I use for repairs, but would not trust them to make the receiver as new. yep --trust is key Quote Link to comment Share on other sites More sharing options...
OO1 Posted December 8, 2020 Share Posted December 8, 2020 Quote Link to comment Share on other sites More sharing options...
OO1 Posted December 8, 2020 Share Posted December 8, 2020 Quote Link to comment Share on other sites More sharing options...
OO1 Posted December 8, 2020 Share Posted December 8, 2020 Quote Link to comment Share on other sites More sharing options...
jimjimbo Posted December 8, 2020 Share Posted December 8, 2020 58 minutes ago, luddite said: I'm in Memphis. And, I've shipped many pieces, including Mac units with the fragile glass fronts, without issue. I'm not afraid to send the reciever off to a good repairman. It will be well packed; I would like the restoration to be the same. I do have a couple of places locally I use for repairs, but would not trust them to make the receiver as new. Sending you a PM. Quote Link to comment Share on other sites More sharing options...
henry4841 Posted December 8, 2020 Share Posted December 8, 2020 This guy knows his stuff and works for a respected shop in California. https://www.youtube.com/c/JordanPier/featured No affiliation but I watch many electronic repair videos. I cannot remember what the name of the shop he works at is right now but do some googling and you should be able to find out. Also there is contact information https://www.youtube.com/c/JordanPier/about. Just one, there are others but the electronic technicians are dwindling especially the good ones. Do some research before sending it out for restoration. It is a prize of a receiver to own and cherish. Quote Link to comment Share on other sites More sharing options...
henry4841 Posted December 8, 2020 Share Posted December 8, 2020 Found it with quick search. http://www.repairaudio.com/about.html Again no affiliation so do not blame me if you send and not satisfied. I do not think it is going to be cheap though. Quote Link to comment Share on other sites More sharing options...
John Warren Posted December 9, 2020 Share Posted December 9, 2020 21 hours ago, luddite said: The good news is that it is fully functional, and works as it should. I would like to have it restored to as new condition. Just use it and enjoy it. When it craps out then think about getting it fixed. Quote Link to comment Share on other sites More sharing options...
luddite Posted December 9, 2020 Author Share Posted December 9, 2020 Thanks to those who have responded, both within the topic and with PM. I have some leads, and will look for others. Major dilemma is where major repairs stop and restoration starts. I would like it to look and work as new; the SX 1250 was a pretty piece. But so far it is serious money for a complete restoration; I'm having to rationalize the cash outlay to do so. While the receiver is collectable now, I wonder if it will keep its value. Quote Link to comment Share on other sites More sharing options...
OO1 Posted December 9, 2020 Share Posted December 9, 2020 be careful not to use reproduction parts Quote Link to comment Share on other sites More sharing options...
henry4841 Posted December 9, 2020 Share Posted December 9, 2020 8 hours ago, luddite said: While the receiver is collectable now, I wonder if it will keep its value. I have no doubt in my mind that it will only increase in value over time. There is a lot of time involved in a complete restoration. Any biz that is trying to make a profit is going to be expensive. With some searching and patience you may find someone that will do the restoration that is retired and competent. My opinion is only those with personal attachment will spend the big bucks with a shop for a complete restoration. This guy is competent from all appearances and does work for a hobby at home. Would not hurt to ask if and what price. https://www.youtube.com/channel/UCRx5TQd00NOjK5D7VB6pHyA Quote Link to comment Share on other sites More sharing options...
luddite Posted December 9, 2020 Author Share Posted December 9, 2020 Another question involves the restoration itself. Old parts are replaced with new, sometimes “as close to original as possible”, and sometimes “to improve the sound”. If I want the unit as original requires one restoration; and an improvement requires another. Like a classic car restored to as it came off the showroom floor VS the same car as a resto mod. And I’m not sure I can tell the restorer which to do. Quote Link to comment Share on other sites More sharing options...
jimjimbo Posted December 9, 2020 Share Posted December 9, 2020 10 hours ago, luddite said: While the receiver is collectable now, I wonder if it will keep its value. Yes, it will. It is worth the money to do a restore. Quote Link to comment Share on other sites More sharing options...
henry4841 Posted December 9, 2020 Share Posted December 9, 2020 A little vague on what the restorer is talking about. If one is talking replacing mica caps with film, sure that is what you want to do. Again if we are talking caps the original value may not be available. Cap values have been standardized to specific values these days. For instance if the old part is 50uf what is available is 47uf and is acceptable. Just an instance. Talk to restorer and see what he means by statement. Another example is a transistor that is known to get noisy over time. You would want it replaced with a modern one with same specs. Clarification is need on what is meant by statement. Quote Link to comment Share on other sites More sharing options...
muel Posted December 9, 2020 Share Posted December 9, 2020 Absolutely a great person to rebuild your SX1250 is Paul of http://www.manymoonsaudio.com/ @paul79 He has done multiple rebuilds for me including a beautiful SX1250! There is quite a backlog so I imagine it will be a long wait but he will replace everything needed with the best parts for the job and what you will get back is better than new. A 1250 is worth the effort. Quote Link to comment Share on other sites More sharing options...
luddite Posted December 9, 2020 Author Share Posted December 9, 2020 It was more I who was vague with the response. ManyMoons website says he rebuilds for the receiver to sound as it was originally designed. Other sites say the unit would be rebuilt to be as good or better than new. But that is in the eyes and ears of the restorer. I like the idea of a restoration as true to the original as possible. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.