CECAA850 29388 Posted February 22 Be sure that none of the wire strands touch any of the other terminals or strands from other wires. 1 Quote Share this post Link to post Share on other sites
billybob 13939 Posted February 22 Looks like how many wire in each speaker line and how many colors? Quote Share this post Link to post Share on other sites
billybob 13939 Posted February 22 1 minute ago, CECAA850 said: Be sure that none of the wire strands touch any of the other terminals or strands from other wires. Help him Carl... Quote Share this post Link to post Share on other sites
CECAA850 29388 Posted February 22 1 minute ago, billybob said: Help him Carl... After looking at that picture, I don't know if i have the patience. LOL. OP, there should be easy to interpret diagrams that came with your speakers and your receiver. I suggest taking a look at them. If you have neither manual, they can be found online. 1 Quote Share this post Link to post Share on other sites
Taap bassi 10 Posted February 22 Looks like how many wire in each speaker line and how many colors?There are about twoSent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
Taap bassi 10 Posted February 22 Looks like how many wire in each speaker line and how many colors?There are about twoSent from my iPhone using Tapatalk 1 Quote Share this post Link to post Share on other sites
billybob 13939 Posted February 22 Without cutting through with a sharp object, cutoff about 2 or 3 inches of the outer clear sheath without cutting into the insulation of the 2 internal wires and remove. Quote Share this post Link to post Share on other sites
Taap bassi 10 Posted February 22 After looking at that picture, I don't know if i have the patience. LOL. OP, there should be easy to interpret diagrams that came with your speakers and your receiver. I suggest taking a look at them. If you have neither manual, they can be found online.I don’t think I have the documents is there anyway someone can hook it up for me?Sent from my iPhone using Tapatalk Quote Share this post Link to post Share on other sites
billybob 13939 Posted February 22 Did you see the last post I made above? Quote Share this post Link to post Share on other sites
Taap bassi 10 Posted February 22 Just now, billybob said: Did you see the last post I made above? Yes Quote Share this post Link to post Share on other sites
billybob 13939 Posted February 22 1 minute ago, Taap bassi said: Yes Do that with a knife or razor. Quote Share this post Link to post Share on other sites
Taap bassi 10 Posted February 22 Just now, billybob said: Do that with a knife or razor. Just did Quote Share this post Link to post Share on other sites
billybob 13939 Posted February 22 3 minutes ago, Taap bassi said: Just did Now should be looking at the unstripped black and white wires. Strip those a good inch making certain wire strands are both even. Quote Share this post Link to post Share on other sites
wvu80 6534 Posted February 22 14 minutes ago, Taap bassi said: I don’t think I have the documents is there anyway someone can hook it up for me? You can do this. I've not jumped in because you've already got expert guidance from the other guys here. The secret is to go slow and not think about how complicated this is. Just do one wire pair at a time, ie Right OUT on the Yamaha to the right-side speaker, The one thing I might clarify is it looks like your speaker wire is twisted inside the sheath. That is a bit unusual, but perfectly OK. What @billybob wants you to do is to cut the plastic sheath back 2-3 inches AND THEN twist the Red wire so you can wrap it around the binding posts, and then do the same to the other wire. +++ I looked very carefully at the picture of the speaker wires. One wire is going to have a marking on it, probably a light blue stripe. Call this the RED wire. So connect RED on the AVR to the RED on the speaker. The AVR will tell you LEFT and RIGHT speakers. 1 1 Quote Share this post Link to post Share on other sites
billybob 13939 Posted February 22 Just now, wvu80 said: You can do this. I've not jumped in because you've already got expert guidance from the other guys here. The secret is to go slow and not think about how complicated this is. Just do one wire pair at a time, ie Right OUT on the Yamaha to the right-side speaker, The one thing I might clarify is it looks like your speaker wire is twisted inside the sheath. That is a bit unusual, but perfectly OK. What @billybob wants you to do is to cut the plastic sheath back 2-3 inches AND THEN twist the Red wire so you can wrap it around the binding posts, and then do the same to the other wire. It's all yours now... 2 Quote Share this post Link to post Share on other sites
wvu80 6534 Posted February 22 @Taap bassi see if this video helps. 1 1 Quote Share this post Link to post Share on other sites
billybob 13939 Posted February 23 Hopefully your all set then. Manual online for features Handbook. How are you making out... Going to ask you about those spliced cables in photo. Make certain splice is correct. Thanks! 1 Quote Share this post Link to post Share on other sites
wvu80 6534 Posted February 23 14 minutes ago, billybob said: Make certain splice is correct. Also put electrical tape around those splices. They are not off-set by a few inches and it looks like they would easily touch the +/- resulting in the AVR going into thermal shutdown. 1 Quote Share this post Link to post Share on other sites
dwilawyer 4200 Posted February 23 Who do they sound? 1 Quote Share this post Link to post Share on other sites
Taap bassi 10 Posted February 23 I believe I’m all good but I have a smart tv and do we just put the hdmi cable to the arc and we don’t have to hook up anything else 2 Quote Share this post Link to post Share on other sites