HDBRbuilder Posted April 18, 2021 Share Posted April 18, 2021 On 3/28/2021 at 11:43 AM, MC39693 said: Welcome to the forum. The Mx may be MI ... it is the initials of the person(s) who built the cabinets, perhaps @HDBRbuilder can shed some light on the initials. The crossover is E2 so this is a version 2 likely 1985 onwards... a picture of the front baffle would help. Others with woodworking skills can chime in to help help with your repairs. Those initials are more likely the sander of the cabinets, but if you gently scrape off the paint below those initials, you will likely find the builder code initial(s)...sanders tended to slather the rear edges of the panels with thinned down wood filler...let it harden, then belt sand those edges. Doing this often resulted in the builder code either getting completely sanded off or at least getting filled with putty and then it got painted over.! So if it is there it is under the paint. The sander code was put on after the sanding was completed...so it tends to always remain prominent, even after being painted-over. The builder code should be right below the sander code....underneath the paint. 2 Quote Link to comment Share on other sites More sharing options...
Howard Emerson Posted April 20, 2021 Author Share Posted April 20, 2021 On 4/18/2021 at 4:28 PM, HDBRbuilder said: Those initials are more likely the sander of the cabinets, but if you gently scrape off the paint below those initials, you will likely find the builder code initial(s)...sanders tended to slather the rear edges of the panels with thinned down wood filler...let it harden, then belt sand those edges. Doing this often resulted in the builder code either getting completely sanded off or at least getting filled with putty and then it got painted over.! So if it is there it is under the paint. The sander code was put on after the sanding was completed...so it tends to always remain prominent, even after being painted-over. The builder code should be right below the sander code....underneath the paint. Hello, Although it's way too late now, in preparing the cabinets for veneering I actually used a cabinet scraper on the front and back 3/4" edges to be more precise in the the removal of the paint. Believe me, there was NOTHING there, and I've since seen several black Heresy originals where the serial # or initials are clear as day. The MI on the back side edge was the only vestige of anything, and it now resides under veneer. Regards, Howard Emerson Quote Link to comment Share on other sites More sharing options...
HDBRbuilder Posted April 20, 2021 Share Posted April 20, 2021 7 hours ago, Howard Emerson said: Hello, Although it's way too late now, in preparing the cabinets for veneering I actually used a cabinet scraper on the front and back 3/4" edges to be more precise in the the removal of the paint. Believe me, there was NOTHING there, and I've since seen several black Heresy originals where the serial # or initials are clear as day. The MI on the back side edge was the only vestige of anything, and it now resides under veneer. Regards, Howard Emerson If I was the one who built them there would definitely be an "A" there...and additional letter if I had a helper that day.. So they were either built after I left in October of '83 OR I had taken a day off and somebody else was at my work table building them. 3 Quote Link to comment Share on other sites More sharing options...
Howard Emerson Posted April 27, 2021 Author Share Posted April 27, 2021 (edited) The drivers and crossovers are all back inside the cabinets where they belong, and yes: There were gaskets on the woofers after all! The Klipsch badges were very discolored, and I assumed that they were made from anodized aluminum, and I believe that is incorrect. Having seen many older Fender Precision basses from the 1950's, anodized aluminum shows plain silver aluminum when it's worn, so I was concerned about using any abrasive to remove the discoloration I was seeing. I threw caution to the wind and started rubbing with a light grey Scotch Brite pad, and the more I worked it, the more coppery the color became! I then switched to a white 1200 Scotch Brite, and it really polished up quite well! Maybe the badges are actually copper to start with? In any case here are some shots showing the detail: Clearly I have to spend a little more time on the ends so I'll have to mask the cloth so I don't mess that up. Here's a shot with the drivers loaded: Edited April 27, 2021 by Howard Emerson 2 Quote Link to comment Share on other sites More sharing options...
OO1 Posted April 27, 2021 Share Posted April 27, 2021 On 4/2/2021 at 7:13 AM, Howard Emerson said: Just unrolled a 4' x 8' roll of rift sawn white oak goodness.........Now to measure very, very carefully and prepare to veneer over the weekend if the fates allow..... real veneer , thick -nothing like the MDF Veneered panels --the veneer on MDF panels is as thin as a sheet of paper - Quote Link to comment Share on other sites More sharing options...
OO1 Posted April 27, 2021 Share Posted April 27, 2021 1 hour ago, Howard Emerson said: The drivers and crossovers are all back inside the cabinets where they belong, and yes: There were gaskets on the woofers after all! Maybe the badges are actually copper Normally there should be a gasket on the woofer , as it must seal with the motorboard and yes , Klipsch badges were copper plate thin gauge , that were stamped embossed with the Klipsch logo then filled with black paint on the recessed lettering - 1 Quote Link to comment Share on other sites More sharing options...
Howard Emerson Posted July 13, 2021 Author Share Posted July 13, 2021 The Silk Purse gets an update of sorts........with pictures...... This morning I'll finally be putting them in the atrium where I've imagined they should look perfect. Hopefully they'll sound at least half as good as they look:-) 7 Quote Link to comment Share on other sites More sharing options...
Area 51 Posted July 19, 2021 Share Posted July 19, 2021 Absolutely BEAUTIFUL! 1 Quote Link to comment Share on other sites More sharing options...
Frzninvt Posted July 19, 2021 Share Posted July 19, 2021 Wow! Amazing transformation. 1 Quote Link to comment Share on other sites More sharing options...
Howard Emerson Posted July 19, 2021 Author Share Posted July 19, 2021 3 hours ago, Area 51 said: Absolutely BEAUTIFUL! And it looks even better in the atrium than it does on a makeshift workbench! 5 Quote Link to comment Share on other sites More sharing options...
Marvel Posted July 19, 2021 Share Posted July 19, 2021 Wonderful job on those, Howard! They look really, really nice! Quote Link to comment Share on other sites More sharing options...
DizRotus Posted July 19, 2021 Share Posted July 19, 2021 You don’t need no stinkin’ Duratex. If I had your woodworking skills and patience I wouldn’t use Duratex, but I don’t, so I do. 1 Quote Link to comment Share on other sites More sharing options...
Bubo Posted July 19, 2021 Share Posted July 19, 2021 Good for you, looks great ! Quote Link to comment Share on other sites More sharing options...
David Evans Posted July 19, 2021 Share Posted July 19, 2021 It all looks great! Fantastic job! Enjoy... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.