wbram Posted May 22, 2008 Share Posted May 22, 2008 I accidently broke the wires off the DIN connector of the BASH sub of my Promedia 4.1. I think I can resolder the wires onto the DIN conenctor that plugs into the sub but I'm not sure what color wire goes where. Does anyone have a wiring diagram showing which color wire goes to which pin on the DIN connector? Thanks in advance for your help! Bill Quote Link to comment Share on other sites More sharing options...
Mister_Clean Posted May 22, 2008 Share Posted May 22, 2008 I need to know what system you have, what color wires do you see? is there a white wire? does your control pod have an on/off button? these are very important not knowing which system you have can damage your current sub amplifiers. let me know and I can send you what you need. Quote Link to comment Share on other sites More sharing options...
wbram Posted May 22, 2008 Author Share Posted May 22, 2008 Thanks for looking into this. I have the ProMedia 4.1 system This is the webpage showing what I have: http://www.klipsch.com/products/discontinued/details/promedia-4-1.aspx The Klipsch PN on the sub says 09050281210, SPARES = 143914-001. The control pod is built into the bottom of satellite speaker. It has no on/off button or earphone jack. The connector I'm referring to is the DIN going directly into the PRE-AMP INPUT on the sub. I have the following wire colors: WHITE, Red, Blue, Black, Orange,Yellow, Green, Brown and ground THANKS! Quote Link to comment Share on other sites More sharing options...
Mister_Clean Posted May 22, 2008 Share Posted May 22, 2008 okay, not a problem at all, you don't have the 4.1 then, you have the v.2-400, it should say that about where the power cable goes into the subwoofer. write to me at damagetone@aim.com and I will send you a color coded diagram that I made for the v.2-400. Quote Link to comment Share on other sites More sharing options...
BrandonM Posted December 26, 2008 Share Posted December 26, 2008 I have the exact same problem, and same system. I e-mailed you, I hope you're still at that e-mail address. My cable broke today and I hope to have it working again ASAP.! Quote Link to comment Share on other sites More sharing options...
matthewcuypers Posted May 2, 2009 Share Posted May 2, 2009 Do you have any type of wiring diagram for the DIN pug . I have the klipsch 4.1 can you help me please. You can contact me at matthewcuypers@yahoo.com Quote Link to comment Share on other sites More sharing options...
Orrick Posted September 7, 2009 Share Posted September 7, 2009 I have the same problem. Would you please send me the wiring diagram for this unit or let me know where to purchase a new input cable? (v.2-400) p/n 09050281210 p/n 143914-001 Quote Link to comment Share on other sites More sharing options...
Mister_Clean Posted September 7, 2009 Share Posted September 7, 2009 I think i can help you out with that, please write to me direct at damagetone@aim.com and we can discuss what I can do for you in this matter. I do believe i have this cable/din setup complete. Quote Link to comment Share on other sites More sharing options...
coltsfan1979 Posted September 11, 2009 Share Posted September 11, 2009 I am thinking that Klipsch Tech Support has a diagram for this. Quote Link to comment Share on other sites More sharing options...
Mister_Clean Posted September 11, 2009 Share Posted September 11, 2009 yeah, they absolutely do have it, but they don't give it out very easily. And alot of people screw their systems up by using the wrong diagram since there are different wiring schematics for the 4.1 and the v.2-400, and one of the schematics that klipsch themselves have given out was in fact wrong. So it can be a tricky thing, but in any case, I no longer give out the diagrams either, I have people send me their units now and I will replace the DIN. I have made some pretty good diagrams though that are still floating around out there if people need them. Look hard enough, you'll find them. Quote Link to comment Share on other sites More sharing options...
satchel Posted September 11, 2009 Share Posted September 11, 2009 http://www.thompdale.com/bash_amplifier/4-1/4-1_bash_amp.htm Quote Link to comment Share on other sites More sharing options...
Mister_Clean Posted September 12, 2009 Share Posted September 12, 2009 Yes, That is an excellent Diagram, if you own one of these systems you should make a copy of that entire file and keep it on hand. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.