zingo

I had a pair custom made for a pair of Fortes by a local plastic shop out of plexi if you want to go that route.

Sold; thanks everyone!

Anyone want to trade for a pre/pro that does Dolby TrueHD?

$400 plus actual shipping; enjoy a great preamp!

Holiday weekend bump!

$500 including CONUS shipping and paypal

I am looking to try surround sound from my current stereo set-up. As an audiophile quality preamplifier, this is everything you need (balanced connections, phono section, inputs with and without tone controls, stepped volume) without complicated set-up and from the top line of a very well respected HiFi company. This Parasound Halo preamp will come with factory remote, manual, and box, and is in very good condition. It's a great unit, but I want to try surround sound for a change; I will also include premium XLR cables and a power cord. -Parasound Halo P3 Preamplifer 6 line inputs, one input switchable to MM phono Relay switched direct inputs: balanced and unbalanced External processor send and receive loop Balanced XLR and unbalanced RCA outputs Defeatable bass and treble controls Enormous encapsulated toroid power transformer Dual layer glass epoxy circuit boards High resolution stereo headphone circuit External IR input and loop output jacks Two 12v triggers; 1 input and 1 loop output Gold-plated RCA jacks Remote control also operates T 3 Tuner

Hmmm... Some how I uploaded the picture sideways... The speakers do sound great powered by the Sunfire with the Parasound P3 in front of it. I haven't run out of power yet, even with powering the subwoofer as well.

I finally pulled the speakers off the walls today to look at the crossovers, and I forgot how large they are! I loose perspective with them hanging on the wall, but pulling them off the french cleats was a quick reminder. The crossovers are actually very well done, in that the freestanding input houses most of the crossover, and the wall mount input only adds two caps to raise the rolloff point of the speaker. Add to that the tweeter, mid woofers, and bass woofers are all isolated from eachother, and the Made In Denmark sticker must be real.

Still available, and I'm willing to do $280 if shipping is near the west coast as it's a bit cheaper for me.

PM returned

I'd saw make me an offer, but I'd already eat quite a bit shipping it to Florida for you. It is a great integrated that I've been using as a preamp lately, and it just deserves more than that; and for me to buy an actual preamp.

The amp works and looks great, and will come with power cord, manual, original remote, and NAD double box; never modified or repaired! Asking $300 shipped CONUS Description: Remote-controlled integrated amplifier with seven line-level inputs (including two tape in/record out); preamp out/main in, and a second preamp out with up to 12dB attenuation; NAD Link; Soft Clipping and Bridging switches. Output power: 120Wpc (20.8dBW), continuous average power into 8 ohms, both channels driven. IHF dynamic headroom into 8 ohms: 3dB. IHF dynamic power (8, 4, 2 ohms): 210W, 340W, 450W. Frequency response: 20Hz-20kHz, ±0.3dB. THD: 0.03%. S/N Ratio (A-weighted, ref. 1W): 94dB. Damping factor (ref. 8 ohm 1kHz): >150. Preamp output impedance: 100 ohms. Headphone output impedance: 220 ohms. Dimensions: 17 1/8" W by 5 ¼" H by 13 13/16" D. Weight: 26.5 lbs.

Good thought about the crossovers, and I'll have see how they're wired as I've only had them wall mounted; 50lbs each and with french cleats no less! All of the drivers are Vifa, seem to be very high quality, and they do sound great!

Thanks ya'll! I will give it a try, and see how those two channels sound on my Jamo speakers. (I know they are not Klipsch, but owned under the same group... ) The speakers aren't bi-wireable unfortunately as the two sets of inputs are for freestanding and wall placement; two different crossovers. However, that power should allow enough headroom anyway; 800w RMS at 4ohm nominal impedance.