Jump to content

Rudy81

Regulars
  • Posts

    3554
  • Joined

  • Last visited

  • Days Won

    2

Rudy81 last won the day on January 21 2020

Rudy81 had the most liked content!

1 Follower

Profile Information

  • Gender
    Not Telling
  • Location
    North Texas

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Rudy81's Achievements

Forum Ultra Veteran

Forum Ultra Veteran (5/9)

518

Reputation

  1. Hmmmm. Placing the back of the speaker so close to the wall is likely to cause you problems and in a sense, defeats the purpose of the dipole design. I don't have any experience with labyrinth use in such a scenario. I suspect you are likely to have to use trial and error to see if that will work for you. I suspect this concept is really adding complexity to your listening space. I would start with just placing the speakers where you want without anything modifying the rear propagation and listen to it. It may sound ok. As I'm sure you know, OB speakers are normally further from the rear wall.....but, trying it out will be the only way for your to figure out how it sounds. If not satisfied, you can the begin trying different options like absorption, diffusion or a much complex idea like the labyrinth. You actually may have good luck using some polycylindrical diffusers on the back wall.
  2. A driver with a Qts of 0.59, to the best of my knowledge, may not work very well in an OB setup. I would think a driver with a Qts above 1.0 would be better suited. Funny you mention Bert's Orelo. I built a set of DIY Orelo horns paired with some 15" Eminence drivers I had and could never get the performance I expected or needed out of them. I'm sure Bert's work well, but I won't be passing by the Netherlands anytime soon to have a listen. I have built and played with just about every type of OB setup and have settled on the very simple H frame configuration with dual 18" Goldwood drivers, it has the best performance when paired with the Heil AMT in a 2-way configuration. I have other conventional Klipsch speakers, but for my room setup, the OB sound is my favorite.
  3. Always interesting to hear 'acoustic' opinions from different ears. I will note that as a dipole driver, it is important to keep it away from the rear walls. In my case, I have mine about 6' from the rear wall and about 3' from the side walls, which have absorbers on them. I have a set of 402's in my shop right now, and the sound is very different between the two systems. IMHO, the AMT is spectacular for a stereo set up in most rooms. My room is fairly large with quite a bit of acoustic treatment.
  4. @Dave A, I guess you did not read the last sentence in the very first post.....
  5. I would seriously consider those for sure, I can't drive up to get them and shipping is not likely. I'm sure someone will jump in.
  6. I wish I was closer to you. I need something like this for my barn. GLWYS!
  7. If you are interested, you can search for opinions on the various computer algorithms like Audyssey etc. I found, once I was objective, that those pieces of software don't work as well as the manufacturers pretend they do. You are way better off without all that stuff. The La Scala is a great speaker and with modern manufacturing methods, the drivers are not the problem. The cabinet is not the problem. Our rooms are the problem. We all have to deal with the rooms we have. Once you focus on that, you will be able to spend your time improving things wisely. As I mentioned, take your speaker outside of the room confinement and run a sweep. You will be able to 'see' that most problems are caused by our rooms. True for every speaker made.
  8. I might suggest you focus on one headache at a time. Take the subs totally out of the equation until you get the LaS dialed in. Get the La Scalas placed so they give you the best possible performance within the limitations of your room and WAF. THEN, and only THEN, go to the REW room simulator and set it up to mimic your room. Then, you will be able to play with the sub locations. That software is particularly good at helping with sub placement. With your subs at the front of the room, you are causing problems in the most difficult frequency ranges. REW will likely suggest one sub up front and one near the back....no, not necessarily in the corners (WAAF again). If done properly, you should be able to place the subs to HELP with placement limitations of the La Scalas, thereby finding an optimal solution for your listening environment. Understand that this process will take quite a bit of time, but it will be worth the effort.
  9. BTW, the La Scala has plenty of bass down to 40Hz or so. Below that, I preferred the Cornwall bass. The Belle was the weakest in the bass department IMHO. Of course, the Khorn trumped them, but they too had their limitations due to placement requirements. At the outset, you just need to understand there is no PERFECT answer that will give you a perfect solution. You can get close, but have to spend horrendous amounts of money to create a proper listening environment. Room geometry and acoustics is where all the challenges and solutions lie.
  10. As you can see in your graphs, the EQ is negatively affecting your response. I suggest keeping the timing measurements for all your speakers, but do away with the EQ being applied. If you are concerned with a reversed driver, just run one speaker and see how it performs in the room. With only one speaker running, the only interaction will be at the crossover frequency. It happens, but is rare IMHO. that the drivers are wired wrong. That, is generally very obvious. If you want to prove to yourself that it is the room interaction with the frequencies, take several measurements at different room locations and focus in on the bass area below about 120Hz. You will likely see some locations with great bass and other results with terrible response at the same frequency but a different measurement location. Using the REW room simulator, you MAY be able to find better locations for your speakers and sitting position. Lot easier to move a mouse or track pad than the speaker and your couch. Be advised, you are entering a very deep and dark rabbit hole.....but rewarding once you understand the limitations and what you can do about them. WAF, however will be huge factor here.
  11. Some of what you are looking at is the effects of your room on bass. Other than doing some type of bass treatment, there is not much you can do to fix that problem. I HIGHLY encourage you to disable YPAO, although I don't have any experience with that system, after many years of working and struggling against Audyssey Pro, I got rid of it and have never looked back. If you get really motivated, and have some open space in your back yard, take one of your La Scala's outside and take a sweep outside. Not quite an anechoic chamber, but will give you an idea of just how much your room affects your performance. I live on acreage, so fairly easy for me to do without any neighbor's houses close enough to affect the results. If you want to look at the theoretical expectation, use the REW room simulation to show you how your room dimensions affect the bass of your system. This is why the listening environment is what we should all focus on to optimize performance, not speaker cables or other snake oils.
  12. @RandyH, nice catch! Sure looks more and more like a scam....not to mention that they are in 'storage'.
  13. Well, at least the post was written by someone who exaggerates just a little. I'm fairly certain they 'originally' were not $17,000. Now, if they were something in the Pro version, I'd be all over them.
  14. Being skeptical is always a good idea!
×
×
  • Create New...