Search the Community
Showing results for tags 'beginner'.
Hi there, Not sure if this subject has been covered, but trying to go through 1000+ topics and nothing's coming up on search. I have the following for my setup: RF-82 (Front) - 33Hz - 23kHz +/- 3dB RC-52 (Centre) - 67Hz - 23kHz +/- 3dB RS-52 (Surround) - 62Hz - 23kHz +/- 3dB Klipsch SW110 sub. Yamaha RXV-675 for my receiver. I've been trying to figure out the right crossover frequency for my setup and I'm just a little lost/confused. The THX guide recommends 80Hz as the general setting if you have a receiver that allows you to only setup Large/Small speakers, however... from what I've been reading and if I understand it correctly, my fronts are rated for 40Hz, my Centre and Surround are rated for 80Hz (since I can't select 70, 80 is next). I've also read that a better choice is to set to set the front speakers as Large instead of Small and do LFE + Front but at 90HZ. This would ensure that all speakers are pushing out just the right frequencies and all the good stuff goes to the front and sub for clean sound. It looks like because of the wide gap of the front and all other speakers that a receiver that lets you configure the crossover individually would work best, but that's not an option now, so striking the right balance is what I can go for. YPAO is useless lol I like doing my configuration manually; measure the distance of speakers and configure levels with a SPL meter. I'm just trying to figure out what the RIGHT crossover frequency is for this setup so it kicks butt. Sounds are either too much bass and possibly overlap the other sounds (sub configured for bypass by turning the low-pass filter at max and controlling crossover on AVR) which is why I have a hard time making out dialogue and surround effects. I've kind of compensated for this by raising the level in the center channel on the receiver and doing the same for sides. When I turn up the crossover I get too little bass and know I'm missing out on what these speakers can do. I also can't tell the difference between regular DTS and DTS-MA... my receiver supports both so content is not the issue. Just looking for what Klipsch can say about this and others so I can gauge what others who have the same issue are doing. Maybe I'm needing more tinkering around...
I humbly admit to being a complete novice with all things home theater and I have attempted to learn as I go along, but going along as proven to be overwhelming with a lot of the science and technical specs out there when trying to set up a basic system. Basically, Black Friday's black hole at Best Buy sucked me in and I splurged on a pair of R-28Fs, a pair of R-15Ms and a pair of R-10SWs (I have 4 other speakers that can be used as surrounds - ALL speakers are rated @ 8 ohms) & I bought what I was told at the time was an adequate Onkyo receiver - which I soon thereafter discovered was woefully underpowering for the caliber of speakers I bought. According to Klipsch's website regarding my pair of R-28Fs, they recommend an AVR that produces between 150-300w RMS @8 ohms since the speakers are rated at 150RMS @8 ohms. In my quest to find an affordable AVR that produces ANYTHING over 150w RMS @ 8 ohms, my eyeballs are slapped with units that cost nearly $2000 and more. I didn't go into this expecting to spend $5000 on what I imagine most of you on these forums would consider a pretty basic introductory system - but that is what I was hoping to start with until I continue to educate myself on putting together a custom system that I obtain audio utopia with - - - but until then, I am stuck with these speakers and have yet to locate an AVR that would sufficently power all of these speakers without forcing me to go to the bank to take out a loan - - but if that's what I have to do, I am about at the point of giving in so I can finally hook up these speakers. Over the phone, one Klipsch rep told me I'd be fine with an AVR that had 125w RMS @ 8 ohms even though their website contradicts that advice....another rep told me that an AVR with 185w RMS is what I'd need - so I just kinda hung it up for a while after all the misinformation. All apologies if this post is redundant or was posted on the wrong board. Can anyone point me in the direction of a respectable AVR that would be able to properly power the speakers I referenced above? I don't have a 3D HDTV (just a reg HDTV) * don't plan on 4K for a while * and will have to wait on Dolby Atmos until I evolve enough with the abundance of info out there that FOR NOW has me stumped with setting up my very first system. Any tips, suggestions or specific instructions would be appreciated as I am learning all of this on the fly. 2-Channel system with the R-28Fs & a subwoofer? Receivers vs. amplifiers? Watts per channel @ 8 ohms that won't potentially damage the speakers by under or over-powering them? sigh.... Thanks a lot!!