Search the Community
Showing results for tags 'brand new'.
Found 2 results
Just got two brand new RP-260F along with a Anthem MRX520 amp. Received the Klipsch sub and center speaker a couple days ago. We hooked up just the sub and two towers and prepared to be blown away by incredible sound. I queued up Steely Dan and hit play. Ah....the music was horrible. No highs. Nothing from the tweeters. Checked and double checked all obvious things. Polarity, inputs, sound settings, nothing. Changed speaker wire gauge (16). Finally we unboxed the Klipsch center speaker and all frequencies were heard and it sounded incredible. How can this happen? Two brand new speakers and both tweeters are out? Does not seem possible. I'm hoping that although I am not new to home audio, I am overlooking something very simple with these speakers. If both tweeters are out I will have to consider returning the entire Klipsch set up and move on to another brand. On a side note, when unboxing the subwoofer there was a loud rattle in the cabinet. Once out of the box and bag and after a little shaking around, a corner support from inside the cabinet came sliding out of the front port of the sub. WTF? Glue is on the support piece but apparently it was not secured well enough since it has been bouncing around in the cabinet for lord knows how long. I'll send that back simply because the cabinet's integrity is compromised but the 260's? I need to understand what I can do different to test these tweeters. We've been looking forward to this audio upgrade in our home for months and this is so disappointing it makes the wife and I quite upset. Suggestions?
teaman posted a topic in Garage SaleHi gang, I was going to set this amp up in my daughter's bedroom but she really doesn't have much interest in it so I am going to sell it instead. I would rather see it go to a new home than sit in a box.UPA-200 - Brand new never opened. I have opened the outside double box but never the inside box so it is still factory sealed. $300 shipped with insurance to the CONUS. I prefer Paypal gift but may be able to work with you. I have bought and sold plenty here in the forum so you can feel confident in this transaction. Private Message me if you need anything!Thanks, TimFeaturesA true audiophile-quality stereo amplifier.Advanced engineering with SMD gain blocks.Wideband, short signal path, class A/B design topology.Top quality parts and construction.Real power easily drives complex loads.Heavy-duty power supply with oversized toroidal transformer.Gold plated five way binding post speaker terminals.Gold plated RCA input terminals.Classic Emotiva styling with rugged solid steel chassis.15mm solid milled aluminum faceplate.Channel status LED’s. (which can be disabled in stealth mode).Remote trigger input and output.115 VAC or 230 VAC with automatic detection and switching.Full protection from all common input and output fault conditions.SpecificationsTopology: Fully discrete, dual differential, high current, short signal path Class A/B.Number of Channels: 2Power Output (rated power; THD < 0.05%): 125 watts / channel (8 ohms; all channels driven).200 watts / channel (4 ohms; all channels driven).Rated Power Bandwidth (at rated power; 8 Ohm load): 10 Hz to 20 kHz + / - 0.1 dB.Minimum Recommended Load Impedance: 4 ohms (which equals one 4 ohm load or two paralleled 8 ohm loads per channel).Frequency Response: 5 Hz to 80 kHz + 0 / - 2 dB.THD + N: < 0.03%Signal to Noise Ratio (8 Ohm load): > 92 dB at 1 watt (A-weighted).> 106 dB at rated power (A-weighted).Damping Factor (8 Ohm load): > 500Speaker Output Connections: Full-sized 5-way binding posts; one pair per channel x 2.Power Supply: 350 VA high current ultra-low noise toroidal power transformer.40,000 uF of storage capacitance.Input sensitivity (for rated power; 8 Ohm load): 1.1 V (for full output; 8 ohms).Gain: 29 dBInput Connections: Unbalanced (RCA); one per channel.Input Impedance: 47 kOhmsTrigger: Trigger Input: 5 - 20 V (AC or DC); < 10 mA input current required.Trigger Output: 12 VDC; can drive any load up to 50 mA.Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched).Front Panel Controls and Indicators: Standby; push button (changes color to indicate Standby or On).Status LEDs (one per channel); illuminate blue for normal operation or red to indicate a fault (may be disabled by rear panel Status LED switch).