Jump to content
The Klipsch Audio Community

gadgtfreek

Regulars
  • Content Count

    501
  • Joined

  • Last visited

  • Days Won

    1

gadgtfreek last won the day on April 23 2015

gadgtfreek had the most liked content!

Community Reputation

164 Excellent

About gadgtfreek

  • Rank
    Forum Veteran
  • Birthday 03/23/1977

Profile Information

  • Gender
    Not Telling
  • Location
    Lower Alabama
  1. Well, really should be fine with the AVR only. New X4500H is acting up so I enacted a return label, and went ahead and called for the upgrade X6500H japan made model. It has a larger and more robust amp section, so it should be fine. Hopefully it comes working 100%...
  2. That one is just film grain. 4K preserves the grain better where on 1080p blu-ray it is somewhat scrubbed. You either like it or you hate it.
  3. Peppermint 1080p blu-ray this weekend. My wife and I enjoyed it, also streamed the Netflix Kirt Russel Christmas flick last night, was entertaining.
  4. After a couple of years away. The system will be a 3.2 setup (have Rythmik 15" subs), with the fronts being RP8000F's and the center being an RP504C. I just bought a Denon X4500H (125w/channel per Denon), and powering 3 speakers it looks like it should be good for 110-115w/speaker looking at 3rd party testing of older 4000 series Denons. I assume these speakers are like the previous models where the AVR will push them well over what they generally need? I don't have space for a large Outlaw or Emo amp in my current stand and don't see a point to the smaller Outlaw 5000 with the X4500H only driving 3 speakers. The 3 Klipsch speakers will be crossed at 80hz and small of course. Glad to be back over on the Klipsch side.
  5. Thanks. I have Reference series sound experience, but nothing with the other stuff like the Heresy line. I know the reviews say the Heresy lacks bass, but I would prob cross at 60 or 80 anyways, I have bass covered. They are running about $400 cheaper a pair right now than RF7 II's. The little slanted bass is a cool idea too.
  6. So, due to display size and stand size, big center is out. I need advice on what Klipsch models would have good dispersion and sound nice in a 2.2 HT (10% 2.2 channel music) at louder volumes. I know RF7-II's are def an option, and then there is Heresy III. The area does have dual 15" high end internet direct subs already. The two Klipsch would set on each side of the display screen (screen is 68" wide), and the subs would be outside the Klipsch so they would not be far apart. Listening range to speaker is about 10feet. Thanks.
  7. Not much magic related related to setting up trims to minus number and pre or post boosting of subs. The sub has a max volume due to driver and design. As long as the avr/preamp sends an adequate signal, the sub will be fine if the trim is minus or plus. You can boost before or after autocalibration. It will just slide where max volume is reached. If you are boosting a lot with movies, you may need additional wooferage to suit your taste. excessive boosting kills headroom and can lead to amp clipping. It also make the bass out of proportion to the rest of the sound. As Scrappydue has said, youthman's problem is to find a new reference level on the avr to work with or move the MLP back. Youthman is correct, the real number may be 4 or 5 db's above what autocalibration is doing. As far as plus sub trim, thats not entirely correct. Many AVR's will clip the analog out signal if driven too much. An owner of the Denon 4520 proved as much at AVS, the answer is to ensure that menu level stays around -3db, or not much more poositive, and increase at the amp. If you have sub trim at +5 in the AVR and try and go to reference volume, that voltage on analog sub out can clip on at the avr. Even sub manufacturers recommend boosting the subs a little after auto eq if it sets them too low, and their recommendation is to not overdrive the line voltage and increase the sub gain so trims are nice and negative in the AVR. Crank up later from the AVR menu. As far as telling him to find a new reference volume, more than one person has said that. I do it every time I auto EQ, and once you figure it out the numbers are just about repeatable after that. He also needsto find a proper sub volume before starting, as has been stated. Audyssey is not voodoo, you just have to follow some simple rules and pay attention to do's and donts.
  8. You fix it by adjusting the reference volume you use if all else fails. Normal reference volume on a Denon/Marantz is 0.0 db. If your speaker bottoms out at -12, test and see what it outputs at 0.0. Say the SPL meter reports 79db at 0.0 master volume. That means the speaker should be 75db at -4.0 db master volume. Make mental note, start using -4.0 as your "reference" volume, and make sure you increase trims on other speakers so that they are 75db at -4.0 master volume. In my case the 64ii hits -12. At 0.0 it is 77db, so I use -2.0 as my "reference" volume and adjust other speakers so that they report 75db at -2.0 volume, not 73db, etc... You need to find at what volume the -12 speaker reports back 75db, and level match all speakers to it at that volume. IF you have more than one, level match all of them to the worst.
  9. I think they were kinda hard on the movie. I mean sure, the plot is messy, but I have seen a lot worse. The battles are great, the AQ and PQ are top notch. These Rythmik subs really thump.
  10. Thats not correct procedure for Audyssey. If you adjust the sub after saving Aud's eq, it won't know you adjusted the gain up on the sub. I full agree keeping trim level on the minus side, most say between -3 and +3db level to keep from over driving the output. The answer is to set the sub gain a little hot before you run Audyssey, if you want to boost, so you have working room in the level menu. For example, my gains are set where one of my subs is -7.0 and the other is -8.5. Once I apply the 5db boost after Aud, the trim levels in the avr menu are -2 and -3.5.
  11. Yep. it is a fun process but you can only do so much without a perfectly designed room. Most of the avg joes dont have that. My next step is to order the room treatments for the back wall, which should be end of the month.
  12. Better than I expected. PQ and AQ were nice.
  13. Now that is an understatement to say the least, lol. Getting that last 10% can take hours to days! A good portion of things you can't fix. I spent two weeks moving crap around and running sweeps with REW. I fixed very little but learned a lot about the room and what moving the speaker does. It's fun up to a point, but then you have to move on and just enjoy your gear.
  14. Pretty much the easiest way to explain it, and someone doesnt know if their house is right or wrong and XT32 is right or wrong until they test the results!
  15. I don't disagree, I was just explaining why they "tweak" distance on the subs. Sometimes it works, sometimes it doesn't. usually works for people that have multiple subs placed in odd spots. XT32 is a great set it and forget it plan other than fixing xover points. I also always recommend someone get a decent SPL meter and just use the -30dbfs and -40dbfs tones in spears and munsil disc 2 to double check level.
×
×
  • Create New...