MEH Synergy

Haha OK then to learn, I will tell you I am 100% confident in what I am saying. I have bridged many amplifiers. If the power output is the same, why does the amp heat up so much hotter and the level must be reduced much further for the same output?

OK since I figure wrong, you are welcome to chime in and give your 2 cents. Do you figure if I feed a bridged mono amp rated at 2400 watts RMS into 4 ohms a 4 ohm load that the power output will somehow not increase as rated over 8 ohm stereo 😏?

This is the problem I have found with reverb. Gear condition is usually not cared about widely and things are misrepresented IMO often. I have made several purchases there.

Damn man that's terrible. Truly sorry to hear that. I hate deals going sour that involve significant effort on one's behalf. I truly hope you find a killer deal on something special close to you to reward your efforts.

All good man. Haha. I just figured people don't wanna listen to us go on and on about how to run a pair of subwoofers paralleled into an amp and what power output will result.

With all due respect, I know what I am doing and talking about here. I know you are very knowledgeable on many things audio, I'm just not sure about the disagreement on this one. Anyhow, got a couple leads on K2s thus far and will close this thread as soon as I find what I am looking for. Thanks.

Right. But my drivers are 8 ohm and 8 ohms. They are not 2 ohms. I have two options, stereo with 500 WPC or 2400 watts RMS bridged mono into 4 ohms, which is what I will be doing.

Awesome. That's why I'm looking for one or perhaps a pair.

I understand what you are saying, and I agree, to a point. Where I disagree with you is that if I feed a four ohm load into an amplifier rated at 4 ohms bridged mono capability with a published power rating on paper, it WILL receive that power rating. I am presenting a 4 ohm load and the subs will get 2400 watts RMS. I don't think a disagreement can exist about that?

I am very confused. Here is the load, currently wired. So you are saying if I feed that nominal load into an amp that is rated at 2400 watts RMS into 4 ohms bridged mono, it will get 1000 watts?

Congrats, I think you'll be quite happy with them. I think you got a pretty solid deal IMO as well. Enjoy!

Not difficult to rewire an NL4 connector and wire subs in series or parallel as needed.

Correct. Running in stereo, each sub is 8 ohms. Wiring subs together will yield 4 ohm load.

Uhhh. What? 500 WPC X 2 = 1000 watts Bridged mono with subs wired together gives 4 ohm load and 2400 watts RMS. Am I missing something?

Np. Subs are 8 ohms. 500wpc isn't enough power for them, 2400 watts is. Hence the bridge. I don't own a K2 and would like to after thinking it over for some time.

Crown macro on the 396s. And done (hopefully 😂) .

Pair of JBL SRX718S subs.

It isn't Bridgeable and it's worth much more than a K2.

Was in discussion with @SWL about buying one or two. Trying to possibly rekindle that deal. Listening if others have one to sell. I'm located in 90713 (socal).

I am actually considering what someone else here said..... I think I may go with crown K2 instead (I'll use the crown macro reference on my speakers instead) .... Who wants to sell me a K2 in nice shape for a deal?

I didn't swear there. Not sure why it starred out the word I used..... I'll substitute grab then haha.

Thanks man. I have a PLX1602 myself. I wouldn't have use for the 1202, but it's a damn good amp and someone should ****** it up from you

Holiday bump

TTT