Search the Community
Showing results for tags 'lfe'.
Found 4 results
Hi Guys I am very much new to amplifiers and speakers of this level. I bought Denon X4500H and Klipsch RP 8000F + R 115 SW just this week. I am reading through a lot of stuff online about best settings to get the best out of the system. I agree that what I like is the best sound for me, but just to have some basics clear, I need some help from the community. I am using the whole system for music listening only. No movies or TV at all. I read about LFE, LPF etc and tried to play with setting the mains to Large/ Small LFE/LFE+Mains and LPF - 120Hz but I do not seem to feel any difference. I was expecting R 115SW to explode my room but its still very nominal. Could you please help me out with some basic settings. Thanks a lot. Vivek
Hi! I've recently added a klipsch sub (r-115sw) to my home audio system, and I was wondering wether to plug my sub and amp though LFE or a RCA Y-splitter. I mainly use my system for music and in regards to that, i've heard differing statements. Some say LFE is the best option for movies and RCA the best option for music. Others even say that for an untrained ear like mine, I wouldn't even notice the difference between LFE and RCA. So what i'm asking is, if my main use for my system is listening to music, should I connect my sub and amp through LFE or RCA? If any of you have any suggestions as to what cable would be good/compatible with my sub, I would be grateful. Thanks!
Hi, I recently got hold of a R-12SW to go with my R-15PM. So my sub is connected to the speaker with RCA/LFE. My question is regarding the setup of the sub to work in harmony with the R-15PM and I don't quite understand the Low-pass. Someone told me to just put it at max(labeled LFE), but couldn't explain any reason behind this suggestion. Does anyone have experience with setting up a sub like this together with my speakers ? I have a really hard time finding the right setting.
I Own a Pioneer Elite SC-63 receiver. I recently purchased a set of RP-250F floorstands for my front left and right channel. I use the R-10SW sub, a Polk audio RM8 Center (budget, junk) and 2 Polk RM8 satellites for surround (chose them for the bi-directional cones, and budget) overall, an introductory home theater with an adequate sound field. My receiver has a feature called advanced MCACC, where i simply plug in the provided sensitive microphone into the receiver, place it at center listening position at ear level, and the receiver does all the dynamic adjustments for acoustics, distance, channel volumes and so on. It does a great job with the distance and channel volumes. The receiver is capable of bi-amping speakers with such an option. I use the top poles of the floorstands with my left and right channels. (yes, I did remove the brass couplers). The receiver specifies that I use the surround-back channels to bi-amp the bottom poles of the floorstands. I'm almost certain I have this setup correctly. I've also went into the receiver menu and setup of the front L+R channels as bi-amp. the final setup for my HT after the full automation MCACC: Front left and right: Large, Bi-amped Center: Small Surround rears: small Surround back: supplemental Bi-amped Front high: not used Crossover frequency: 150Hz I have 2 LFE sub outs: I use one LFE out to the sub, the LFE is rolled all the way up on the sub, and the gain is rolled back to about 1/4-1/3 of the way from zero. (any more, and the automation complains that the sub gain is too high) my problem: Front channels set to large...Is this right, considering I'm bi-amping? and the crossover frequency set so high? 150hz seems high considering the capabilities of the floorstands. Also, will my rear surrounds suffer if I bring my crossover down to 80hz? I know the receiver is much smarter than me, however when I'm jamming to zepplin or frampton, I use the EX. Stereo option on my receiver. This in my opinion, creates the most magnificent sound field in my living room, but I'm afraid my satellites will suffer from the lower crossover frequency. I listen to music at moderately high, to holy shit volumes. P.S. When I watch a bluray, Such as The Avengers, or Dark Knight rises, I aim for sharing my home theater experience with the neighbors on the backside of my property. I want to experience the Hulk, smashing.