Dieter Posted August 21, 2002 Share Posted August 21, 2002 Hi, In my new home i will have no place for the klipschorn bass, so i decided to builed another enclosure with the K33E. I think the best for me is the cornwall. That's my question: can anybody tell me the volume ( inner dimension) of the cabinet and the dimensions oft the vents(s). Thanks Dieter ------------------ Bass: Klipschorn MidsHighs: TAD 4001 + 22" Horn SuperHigh: Fostex T925 X : active (Pioneer D-23) Pre : AVM V1 Amp : AudioValve PPP 30 : Rotel RB 956 : Quad 303 CD : Marantz CD 73 Quote Link to comment Share on other sites More sharing options...
Klipschguy Posted August 21, 2002 Share Posted August 21, 2002 Dieter, I took off the back of one of my Cornwalls today and carefully measured all the internal dimensions. I don't have time to list them tonight, but I will tomorrow. Andy Quote Link to comment Share on other sites More sharing options...
Dieter Posted August 21, 2002 Author Share Posted August 21, 2002 Hi Andy, great, thank you very much!!! Regards Dieter ------------------ Bass: Klipschorn MidsHighs: TAD 4001 + 22" Horn SuperHigh: Fostex T925 X : active (Pioneer D-23) Pre : AVM V1 Amp : AudioValve PPP 30 : Rotel RB 956 : Quad 303 CD : Marantz CD 73 Quote Link to comment Share on other sites More sharing options...
Klipschguy Posted August 22, 2002 Share Posted August 22, 2002 Internal measurements for 1977 Cornwalls type CWO. 1. internal width: 23 7/8" 2. internal length: 34 1/4" 3. internal depth: 13 1/2" 4. port: 9 1/2" x 22 3/8" x 3 1/8" 5. port holes in motorboard: 10 1/2" x 2 3/16" 6. motorboard inset: 5/8" 7. back: flush Notes: -cabinet depth from INSIDE of back to INSIDE of front -depth of port measured from BACK of motorboard -sides of port are two 3/4" plywood pieces = 9 1/2" -port + cabinet measurements are INTERNAL dimensions -port slots in motorboard has 7/8" wide middle divider -port slots also leave a 7/8" band along bottom edge -port slots not quite flush with top port edge 3/32" -all panels 3/4" (3/4" designated ply is actually less) -cabinet lined with 5/8" insulation, unknown material -all measurement done at least twice Hope this helps, Andy This message has been edited by Klipschguy on 08-22-2002 at 08:33 AM Quote Link to comment Share on other sites More sharing options...
Klipschguy Posted August 22, 2002 Share Posted August 22, 2002 One note to avoid any confusion. There is no divider inside the port. It is one large port hole. The port divider is only on the motor board. Andy Quote Link to comment Share on other sites More sharing options...
Dieter Posted August 22, 2002 Author Share Posted August 22, 2002 Andy! THANK YOU VERY, VERY MUCH!!!!! Grettings from Germany Dieter ------------------ Bass: Klipschorn MidsHighs: TAD 4001 + 22" Horn SuperHigh: Fostex T925 X : active (Pioneer D-23) Pre : AVM V1 Amp : AudioValve PPP 30 : Rotel RB 956 : Quad 303 CD : Marantz CD 73 Quote Link to comment Share on other sites More sharing options...
Klipschguy Posted August 22, 2002 Share Posted August 22, 2002 Dieter, You are quite welcome. By the way, I edited the above post a little to make it a clearer (basically reiterating that all measurements are INTERNAL). Cheers, Andy Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.