afshin1 Posted June 6, 2007 Share Posted June 6, 2007 Hi im new here and im trying to figure out what would be the best way to hook up my sub?i hane a hk 347 and i need to know if ishould use a single rca to the left or use a y splitter and run to rca,s to the left and right of the sub? and also i dont know what to set the crossover to. thanks Quote Link to comment Share on other sites More sharing options...
tenzip Posted June 6, 2007 Share Posted June 6, 2007 Single RCA will work fine. Set the crossover on the sub itself to the max, 120Hz, or whatever. Just crank it all the way up. Then set the crossover in your AVR to 80 to start with. Only one crossover should be used. And welcome to the forum. Quote Link to comment Share on other sites More sharing options...
afshin1 Posted June 6, 2007 Author Share Posted June 6, 2007 thanks i'll do that and let u know. Quote Link to comment Share on other sites More sharing options...
MatrixDweller Posted June 7, 2007 Share Posted June 7, 2007 At first I ran a single RCA to the left on my sub and it sounded great. I decided to try a splitter out at the sub end so the the single RCA split into the left and right. I, as well as a fellow audiophile, noticed a little bit of a difference for the better. I'm not sure why. Quote Link to comment Share on other sites More sharing options...
MatrixDweller Posted June 8, 2007 Share Posted June 8, 2007 Does anyone know why there might be a difference when hooking a splitter up on the L/R sub inputs? Could it be that my splitter is coloring the output? Quote Link to comment Share on other sites More sharing options...
kelA Posted June 8, 2007 Share Posted June 8, 2007 Some people will say adding a y-cable adds 3db to the output. Quote Link to comment Share on other sites More sharing options...
sivadselim Posted June 8, 2007 Share Posted June 8, 2007 Does anyone know why there might be a difference when hooking a splitter up on the L/R sub inputs? I, as well as a fellow audiophile, noticed a little bit of a difference for the better. I'm not sure why. That's anecdotal evidence and it also represents expectational bias. To really see if there was a difference in sound quality, and not simply the volume, you'd have to do a proper double-blinded test, making certain that the sub's output was level-adjusted in each circumstance. Using both inputs simply increases the volume of the sub at any particular volume and subwoofer trim level setting in the receiver. This same volume increase can also be easily obtained with the single RCA cable connection by simply turning up the volume level at the subwoofer, itself. Quote Link to comment Share on other sites More sharing options...
CAS Posted June 8, 2007 Share Posted June 8, 2007 Does anyone know why there might be a difference when hooking a splitter up on the L/R sub inputs? I, as well as a fellow audiophile, noticed a little bit of a difference for the better. I'm not sure why. That's anecdotal evidence and it also represents expectational bias. To really see if there was a difference in sound quality, and not simply the volume, you'd have to do a proper double-blinded test, making certain that the sub's output was level-adjusted in each circumstance. Using both inputs simply increases the volume of the sub at any particular volume and subwoofer trim level setting in the receiver. This same volume increase can also be easily obtained with the single RCA cable connection by simply turning up the volume level at the subwoofer, itself. Exactly correct. It gives you no advantage (unless you think it looks cool). It's the very same thing as turning your sub up a notch. Save your $. Quote Link to comment Share on other sites More sharing options...
Jay481985 Posted June 9, 2007 Share Posted June 9, 2007 it adds 3db but that helps the amplifier get taxed less.... Expecially for those subwoofers with a low gain in. Quote Link to comment Share on other sites More sharing options...
sivadselim Posted June 9, 2007 Share Posted June 9, 2007 it adds 3db but that helps the amplifier get taxed less.... Expecially for those subwoofers with a low gain in. [:^)] It (supposedly) adds 3dB if everything else is left the same, but in recalibrating the sub, the volume would be decreased by those same 3dB, either in the receiver or at the sub's volume knob. A long as you recalibrate your sub, the amp would work exactly the same amount. [] BTW, the "3dB gain" is often cited because people assume that "if you double the input (with the extra connection), you double the sub's output". But that's not really how it works. Using the Y-connector doesn't double the input, it sums the inputs, so there's not really a 3dB gain. [8-|] Quote Link to comment Share on other sites More sharing options...
Jay481985 Posted June 9, 2007 Share Posted June 9, 2007 but as I said it helps with a low output lfe channel Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.