[Tweeter Performance (or lack of)]

Yes. If it does not register any impedence or makes no sound usually means the diaphram is burnt out.

[Right amp for the job?]

What ever amp you get you need to have a filter to limit low frequency to the reflex subs at the frequency the cabinet unloads the driver, probably around 35 or 40Hz. Also, I always suggest getting all the power you can get. Low frequencies suck power.

Hope this helps.

[Hersey II crossovers]

Are the crossovers mounted on the back of the terminal board?

[Heresy autoformer settings]

djk, thanks.

[Heresy autoformer settings]

When you say add a 15ohm resistor in parallel with the mid, does that mean in the + line or in the - line? I am a crossover dummy.

I put a 16 ohm resistor across the mid terminals and I am using tap 1 for the mid and tap 2 for the tweeter. So do I have the resistor attached wrong?

Thanks to you and Moray for your help

[Heresy autoformer settings]

I just recently obtained a set of Heresy w/K53 driver and k 701 horn and type E crossover. What are the factory settings on the autoformer and can they be changed for different output level for the mid and tweeter?

[Heresy cabinet]

Thank you.

[Heresy cabinet]

Is there any type of cabinet lining in the Hersey I and how much for example; R13 insulation lining the walls or stuffed.

Thanks,

biglaz

[mounting drivers from the inside like heritage speakers]

Thanks for the tip.

[mounting drivers from the inside like heritage speakers]

I am building new cabinets for a pair of heresy I speakers. Does anyone have any tips on how to get the drivers mounted on the back side of the baffle ie; get the centered etc.

Thanks,

[K-77 square magnet vs. round magnet tweeters]

Thanks to both responders. You have helped me a great deal.[]

[K-77 square magnet vs. round magnet tweeters]

Are there any signifigant differences between these drivers. I have 1 of each and would like to use these in a heresy project. Or should I hold out and try to get 2 of the same?[*-)]

[F/S KP 480 -Ramsa WP1400 -KSM Monitor(Sold)]

Are the JBL 2042H drivers 18" subs?

[F/S KP 480 -Ramsa WP1400 -KSM Monitor(Sold)]

Is $150.00 for a pair of speakers and cabinets? Would you be interested in selling just the drivers and shipping to 40160?

[WTB-Turntable]

Very nice looking table. Thanks I will consider this however, it is a little over my price range.

[WTB-Turntable]

Could you provide pictures. I may be interested if the table is still available.

Thanks,

[Stereo Subs]

You could use a one into two pigtail. Need 2. single end to the output of the receiver, the other end with 2 female rca to each channel of one sub. Do the same with the other channel.

I'm not sure the above makes any sense or not. The pigtail will have 1 male rca with 2 female rca. Need 2. Get them at Parts Express.

[Adding an equalizer to a home theater receiver]

Thanks. I got it to work.

[Adding an equalizer to a home theater receiver]

Thanks to everyone for the responses!!!

[Adding an equalizer to a home theater receiver]

How do I use the pre-outs?

[Adding an equalizer to a home theater receiver]

I want to use an older ADC eq that has been gone through and now works perfectly.

[Adding an equalizer to a home theater receiver]

I have a Marantz SR 8000 and I want to add an equailizer. Is this possible or am I out of luck?[:|]

[Netflix]

What brand is your AVR?

[Dean Wescott (deang) could use our help!]

I'm in. Get haelthy Dean.

biglaz

[question about Harman Kardon 3490]

Just a reminder the tape out are attenuated. Therefore, the external amp has to have gain controls.

sit back and listen!

biglaz