Duke Spinner Posted November 5, 2006 Share Posted November 5, 2006 22 X 14 that's reg'lar automotive paint, single stage urethane Quote Link to comment Share on other sites More sharing options...
chops Posted November 6, 2006 Share Posted November 6, 2006 Boy, and I thought having three Altec 511B horns staring into my chops was a lot of horn! WOW! Those JBLs are monsters! I'd love to hear those things. BTW, do both woofers cover the same range, or is the bottom one crossed over lower than the top one? I ask because I'm getting ready to design dual 15" bass bins for my mains. Quote Link to comment Share on other sites More sharing options...
Duke Spinner Posted November 6, 2006 Share Posted November 6, 2006 check out the x-over for a JBL 4435, Chops....... one is a mid-bass driver Quote Link to comment Share on other sites More sharing options...
chops Posted November 6, 2006 Share Posted November 6, 2006 Thanks! [] Quote Link to comment Share on other sites More sharing options...
Duke Spinner Posted November 6, 2006 Share Posted November 6, 2006 I meant to give ya the woofer model #'s, Chop's ... that speaker, is basically a 4435, with the horn a 2360 rather than 2344 horn the woof's are both 2234's, one active below 100 hz, they x-over to the 2360 @ 1000hz the slot comes in at 8k... Quote Link to comment Share on other sites More sharing options...
chops Posted November 7, 2006 Share Posted November 7, 2006 Well thanks again! That makes a little more sence. LOL [] Quote Link to comment Share on other sites More sharing options...
colterphoto1 Posted November 7, 2006 Share Posted November 7, 2006 sense Quote Link to comment Share on other sites More sharing options...
chops Posted November 7, 2006 Share Posted November 7, 2006 sense Hey look, it's typo-police!... clown.[8-|] Quote Link to comment Share on other sites More sharing options...
colterphoto1 Posted November 7, 2006 Share Posted November 7, 2006 That's Spelling Police, I don't police typos, your on you're own there. That last bit is for the Grammar Squadron, Now are you gonna be Tough or Sensitive? It's difficult to imagine someone could be both. Quote Link to comment Share on other sites More sharing options...
ZAKO Posted November 7, 2006 Share Posted November 7, 2006 Regardles of the horn type....Finding a HF driver 400hz to 18k hz is almost impossible. I am certain all of you are wizzing in the wind. Get a towel. Quote Link to comment Share on other sites More sharing options...
chops Posted November 7, 2006 Share Posted November 7, 2006 That's Spelling Police, I don't police typos, your on you're own there. That last bit is for the Grammar Squadron, Now are you gonna be Tough or Sensitive? It's difficult to imagine someone could be both. Again, no comment... Quote Link to comment Share on other sites More sharing options...
colterphoto1 Posted November 7, 2006 Share Posted November 7, 2006 yeah I got your PM chops. Quote Link to comment Share on other sites More sharing options...
PrestonTom Posted November 7, 2006 Author Share Posted November 7, 2006 Regardles of the horn type....Finding a HF driver 400hz to 18k hz is almost impossible. I am certain all of you are wizzing in the wind. Get a towel. Maron, I suspect that you are probably correct. Crossing at 700 Hz (or so) is one thing, but at 400 Hz (or even 500) is going to be problematic. -Tom Quote Link to comment Share on other sites More sharing options...
bodcaw boy Posted November 7, 2006 Share Posted November 7, 2006 Regardles of the horn type....Finding a HF driver 400hz to 18k hz is almost impossible. I am certain all of you are wizzing in the wind. Get a towel. the bnc de75 goes from 500 hz to just above 19khz. the k-69 goes from about 600 to also above 19k hz. the tad's 3' diap comp drivers go from about 800 to above 20k hz. boy!! Quote Link to comment Share on other sites More sharing options...
djk Posted November 8, 2006 Share Posted November 8, 2006 TAD makes 100mm and 48mm models. Voice coil diameter: 1-7/8 inches/48mm Equalizing System: 3 slit type. Frequency Range: 450-27,000 Hz. Rated input power: 10 watts The older model diaphragms mat be crossed at 500hz. Deformation is prevented by a surround formed of a special high-polymer compound. It also effectively prevents fatigue and rupture caused by an excessive input level. The newer model of diaphragm has a pure beryllium diaphragm, and must be crossed at 1Khz for its higher 20W rating. All the 100mm models are pure beryllium diaphragm. I have some of the new JBL 76mm pure beryllium diaphragm models. They will make a nice two-way on the right horn with a crossover at or above 650hz. Quote Link to comment Share on other sites More sharing options...
PrestonTom Posted November 8, 2006 Author Share Posted November 8, 2006 Thanks for the input. My question was in relation to a Klipschorn bass bin. I am reluctant to try and cross the bass bin at more than 500Hz. So I am leary about using a driver (still not sure about the horn) that would cross at 600 or 650Hz. Thanks, -Tom Quote Link to comment Share on other sites More sharing options...
sfogg Posted November 8, 2006 Share Posted November 8, 2006 Tom, Altec ran 902s in pro sound settings (theaters) with 500hz crossovers all day long. On a 511B they load to a little below 400hz. See this thread: http://forums.klipsch.com/forums/thread/276873.aspx If you want to give the 902s a try I have a pair I'm not using. Shawn Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.