forte Posted February 20, 2001 Share Posted February 20, 2001 I purchased speaker cables are terminated with spades, since it appears that most people here believe that spaces provide a better connection than bananas, however I am having a problem getting the nut on the binding post tight enough. In order for the spade to be effective it has to be slightly crushed under the nut so that it is flat, otherwise it is not making full contact around its entire body. The nut on the binding post is plastic, and hand tightening does not seem to be enough. I don't want to use a wrench or pliers on the plastic nut, but how do I get it tight? I am starting to think that I would have been better off with bananas. I thought about replacing the nuts with metal ones, but I have read too many articles about peoples binding posts comming loose from behind. That happened to me with another pair of Klipsch speakers. I am trying to connect to RF-3's. Any suggestions? Quote Link to comment Share on other sites More sharing options...
myram Posted February 20, 2001 Share Posted February 20, 2001 Well the only way I found to effectively tighten the binding posts to the spades was to use a pair of pliers. But I really didn't like that idea. So I went with banana plugs that make it much easier to connect and disconnect from the speakers if you have to move them. As far as signal loss from the banana plugs.....that is all BS. As long as you use a good pair of gold plated banana plugs you aren't going to lose any noticable signal. Good Luck. ------------------ Klipsch Quartets Adcom GFA-555 Musical Concepts Modified NAD 1600 Pre/Tuner Sony C-67ES CD Player Quote Link to comment Share on other sites More sharing options...
T2K Posted February 20, 2001 Share Posted February 20, 2001 forte,go to your nearest Tweeter store and tell them you would like a double handfull of Phoenix Gold dual banana plugs.They will cost you about $5 apiece.After installing on speaker wire, insert into back of binding post.If the banana is not snug in plug,use a razor cutter blade or some other thin device to GENTLY pry the plug ends open to achieve a tighter fit.You'll have a large contact surface and ease of use.Enjoy! Keith Quote Link to comment Share on other sites More sharing options...
myram Posted February 20, 2001 Share Posted February 20, 2001 Better yet..when you are at Tweeter or whatever your local store is.....just get the banana plugs that will accept spade connectors. At Tweeter they are made by Niles and cost like $10 for the pair, that is what I use and they are great. ------------------ Klipsch Quartets Adcom GFA-555 Musical Concepts Modified NAD 1600 Pre/Tuner Sony C-67ES CD Player Quote Link to comment Share on other sites More sharing options...
SickPuppy Posted February 20, 2001 Share Posted February 20, 2001 Either way should be fine actually.As long as it's good and snug you dont have to crush a spade connector to make it work correctly.That would be the same as saying a banana plug should be tight enough to almost split it's housing! In reality, a spade connector will give you twice the surface area of MOST banana plugs anyway, not all but most. Myself, I use bare wire, being one that feels the less differnt kinds of metal the better and the less connections the better too. Of course some will say but what about oxidation!? It's a head game..... whatever you like the best, is the best....for you. Quote Link to comment Share on other sites More sharing options...
MartyK Posted March 6, 2001 Share Posted March 6, 2001 The last time I was at my local stereo shop I noticed that they had a wrench for about $10 that was specifically designed to tighten the binding posts by hand. Maybe you can find something simular in your area. Quote Link to comment Share on other sites More sharing options...
johns02 Posted March 6, 2001 Share Posted March 6, 2001 Just go to NAPA Auto Parts for terminals They dont corrode or rust and are cheap Quote Link to comment Share on other sites More sharing options...
BobG2 Posted March 11, 2001 Share Posted March 11, 2001 I use a 1/2" socket and HAND tighten using it for enhanced leverage. You can then get the binding post sufficiently tight on the spade lug and avoid spinning the binding post loose. Cheap trick. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.