Jump to content
The Klipsch Audio Community

rosey

Members
  • Content Count

    35
  • Joined

  • Last visited

Community Reputation

13 Good

About rosey

  • Rank
    Member

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. hi chris, could you please explain why you decided on using the bms 4592 pb be on your meh 402 over a radian, faital, tad, 691, etc.? would you use the bms for your left right if you couldn't use your tads? merry christmas!
  2. well chris, I'm all ears👍
  3. wow, now youve got me thinking! so these education sessions, how does one find out what the schedules are? would obviously want the jubilee 402 system to be on the itinerary. thx for the tip
  4. hi all, well as most of my projects go, this one is going slower than I'd like. my question to the 402 users out there at this point is, which would you think would be superior. jubilee 402 2 way or 3way? 3 way would only consider the bms4592 be coax. 2 way are several good 500-20khz + - options. 2 way would free up some nice rack space, chassis and remote p/s. 2 or 3 way would likely be my border patrol 300b valves on mid/highs, 8 watts tweeters, 20 watts mids, or 20 watts on the coax, and k2s on the jubs. also have a crown 4002 xti for future sub if HT use gets in the mix. my musical tastes lean towards acoustic, singer song writer, blues, acoustic jazz, classical, occationally loud rock. ld appreciate your opinions. rosey
  5. thx jason, I've pm'd @SWL
  6. that makes total sense, just keep reading about supplier problems, unavailability or lesser quality than earlier versions. I will try contacting klipsch again, dont think roy needs to be bothered with something like this, just hope there's replacements available. thx again
  7. I already have done that, but thankyou
  8. I haven't even bothered to haul them upstairs until drivers have been updated and some cosmetics have been completed before contacting deqx support to start initial calibration. it was my understanding that the k 31 e was no longer available.
  9. I haven't even bothered to haul them upstairs until drivers have been updated and some cosmetics have been completed before contacting deqx support to start initial calibration.
  10. thank tom, I totally agree with your use some engineering thought. the problem I'm dealing with is I've got 2 labeled k 31 e drivers installed from 2 different suppliers and they are definitely not the same. 1 I has a mfg date of aug 2016 with pulp style cone. the other jub has a different supplier code and a very light,thin, plastic cone that can be quite easily deformed. light duty? and the other 2 drivers are aftermarket that I have already found a buyer to fund a consistent driver compliment. not looking to be a Guinea pig. was hoping a quality solution had been determined. thx much.
  11. also,fyi. I have submitted the same request to klipsch support a few weeks ago. I know their busy.
  12. thanks tom, done. since this can has been opened, I too am on an upgrade path for my reciently recieved 535b jubilee 2nd hand set. has there been any general consensus amongst the community on a particular bass driver/ drivers as replacements/ upgrades for the k 31 e OEM's?
  13. has there been any consensus amongst the community on replacement/upgrade drivers for the jubilee woofers? I've been searching the forums, and seems the only conversations are from 10-12 yrs ago.will be needing to replace what is currently installed and looking for best recomendations. thanks as always
  14. since this can has been opened, I too am on an upgrade path for my reciently recieved 535b jubilee 2nd hand set. has there been any general consensus amongst the community on a particular bass driver/ drivers as replacements/ upgrades for the k 31 e OEM's? thx much
×
×
  • Create New...