absolve2525 Posted May 22, 2013 Share Posted May 22, 2013 I'd like to try out some of the other crossovers, such as the Type A etc, and was wondering if I can use the autoformers from my AK2? Do I need to start over with all new parts? Thanks for any input! Quote Link to comment Share on other sites More sharing options...
djk Posted May 23, 2013 Share Posted May 23, 2013 I suppose you could use the T5A, but I would use the Crites 3636 and leave the AK2 intact. http://www.critesspeakers.com/3636atz.pdf Quote Link to comment Share on other sites More sharing options...
Deang Posted May 23, 2013 Share Posted May 23, 2013 You have a split crossover. There are two halves. One half, the part for the bass or low pass, is located on the inside of the door going into the bass bin. The other half, or high pass, sits in the top hat -- this is why there are long jumpers leading from binding posts on the door to the network section you can actually see. To use other crossovers, the components in the bass bin either need to be removed or disconnected. Complicating things further is that all of the wiring is soldered to the crossover, which makes trying new crossovers even more difficult. Maybe for now you could just stay with the AK-2. Why not just replace the capacitors in the high pass section and see if you like what you hear. The AK-2 attenuates the squawker down a bit more compared to the others, and a lot of people prefer that anyways. You need two 13uF (you can use 12uF), and six 2uF capacitors to get it done. I don't recommend cheaping out since the crossover sits between the gear and the drivers. So, you kind of have to decide how important the end result is to you and what you are willing to spend before you start. I prefer film and tin foil capacitors whenever possible, and especially in tweeter sections. They are expensive, but a worthwhile investment. If you really want to try different crossovers, then you have some work to do before you can try them. Quote Link to comment Share on other sites More sharing options...
absolve2525 Posted May 23, 2013 Author Share Posted May 23, 2013 Thanks for the reply! What caps need replacing inside of the bass bin? I didn't see any electrolytic caps on the top hat crossovers; I figured they were still good, unlike electrolytic that drift out of spec. . Quote Link to comment Share on other sites More sharing options...
Frzninvt Posted May 28, 2013 Share Posted May 28, 2013 The AK-2 can be easily upgraded to an AK-3 by switching to the T5A autoformer and changing the caps in the woofer door from it's current 70uf (35uf X 2) to 100uf (50uf X 2) and changing the coil to a 5mh I think but it has been awhile. The AK-2 was not that great sounding, so I modified it to be an AK-3 which is a bit better. I did this on my '88 Klipschorn's. This is probably the cheapest approach other than getting some of DeanG's or ALK Engineering networks that can easily best the AK-3 at a price. Kimber's, Solen's or Dayton's are decent caps. Auricap Theta's are really good but pricey. Quote Link to comment Share on other sites More sharing options...
absolve2525 Posted May 28, 2013 Author Share Posted May 28, 2013 Thanks for the comparison to AK3! What differences did you notice when comparing to AK2? Do you know if T5A is available from Klipsch or if Crites offers one? Quote Link to comment Share on other sites More sharing options...
djk Posted May 28, 2013 Share Posted May 28, 2013 The AK2 has 140µF vs the AK3 having 100µF. The AK2 has the T5A and 4mH vs the AK3 having the T4A and 5mH. The Crites 3636 can replace either. Quote Link to comment Share on other sites More sharing options...
Frzninvt Posted May 29, 2013 Share Posted May 29, 2013 Thanks for the clarification Dennis it has been a number of years since I did the update. I bought the T4A's from Klipsch but Crites 3636 offers more flexibility over the T4A. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.