joessportster Posted December 25, 2019 Share Posted December 25, 2019 Any help appreciated, I know its Audio Technica but cant find the model !!!!!!!!!!!! Anyone ? Quote Link to comment Share on other sites More sharing options...
dirtmudd Posted December 26, 2019 Share Posted December 26, 2019 do you have it in your possession ? Quote Link to comment Share on other sites More sharing options...
bkwa1959 Posted December 26, 2019 Share Posted December 26, 2019 records precisely. Due to its stability, it has been used widely in radio stations. Elliptical Styli To reduce the tracking distortion and pinch-effect of a conical stylus, the elliptical stylus is made with a smaller effective radius to overcome these two conditions and provide more detailed audio content. Line Contact Styli (Special Line Contact, Shibata, MicroLine®) Having a0 On the Para-toroidal generating system, since leakage of magnetic flux in this continuous and unitised magnetic circuit is low, a superb linearity can be obtained. Permeability of the cores is also optimised through the use of laminated cores. Centre shield plate between stereo channels A permalloy centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB Yoke Left channel recording direction Right channel Magnet Laminated core Coil Magnet Left channel 05 Cutter stylus Stylus chip Product Information Line Contact Styli Special Line Contact Nude Rectangular Shank VM760SLC DUAL MOVING MAGNET STEREO CARTRIDGE Shibata Nude Square Shank Using an ultra-lightweight stylus tip ground to a high level of precision, we have achieved a combination of low distortion rate with fuller frequency reproduction during playback. This stylus tip extracts every possible piece of information from the grooves on a record. • Aluminium tapered cantilever • Para-toroidal coils improve generating efficiency • Centre shield plate between the left and right channels reduces crosstalk • Die-cast aluminium alloy housing reduces vibration and adds a natural electrical shield VM750SH DUAL MOVING MAGNET STEREO CARTRIDGE Fitted with the Shibata stylus, which was developed for playing 4ch vinyl records that demand high-frequency reproduction capabilities during playback. Not only high- frequency, it is also ideal for reproducing rich mid and low frequencies. • Aluminium tapered cantilever • Para-toroidal coils improve generating efficiency • Centre shield plate between the left and right channels reduces crosstalk • Die-cast aluminium alloy housing reduces vibration and adds a natural electrical shield 06 Product Information Line Contact Styli VM740ML DUAL MOVING MAGNET STEREO CARTRIDGE High-end model featuring a MicroLine® stylus in an aluminium die-cast alloy body. In addition to outstanding high-frequency reproduction, this model enables clear sound image localisation. • Aluminium tapered cantilever • Para-toroidal coils improve generating efficiency • Centre shield plate between the left and right channels reduces crosstalk • Die-cast aluminium alloy housing reduces vibration and adds a natural electrical shield MicroLine® Nude Square Shank MicroLine® Nude Square Shank VM540ML DUAL MOVING MAGNET STEREO CARTRIDGE Standard model with a MicroLine® stylus. Distortion is low even on the inner circumference of a record because the curvature radius of the stylus tip does not alter even if the stylus becomes worn. • Aluminium tapered cantilever • Para-toroidal coils improve generating efficiency • Centre shield plate between the left and right channels reduces crosstalk • Durable low resonance polymer housing VM540ML/H DUAL MOVING MAGNET STEREO CARTRIDGE WITH HEADSHELL 07 Product Information Elliptical & Conical Styli VM530EN DUAL MOVING MAGNET STEREO CARTRIDGE High-end elliptical stylus model equipped with a light-weighted nude elliptical stylus to reduce the execution mass of the vibration system. This enables fuller frequency reproduction. • Aluminium cantilever • Para-toroidal coils improve generating efficiency • Centre shield plate between the left and right channels reduces crosstalk • Durable low resonance polymer housing VM520EB DUAL MOVING MAGNET STEREO CARTRIDGE Standard elliptical stylus model equipped with an elliptical bonded stylus. This reduces tracing distortion and allows for more accurate sound reproduction. • Aluminium cantilever • Para-toroidal coils improve generating efficiency • Centre shield plate between the left and right channels reduces crosstalk • Durable low resonance polymer housing VM510CB DUAL MOVING MAGNET STEREO CARTRIDGE Entry-level VM cartridge model equipped with a conical bonded stylus. The round stylus is less likely to be affected by placement and boasts stable tracing performance. • Aluminium cantilever • Para-toroidal coils improve generating efficiency • Centre shield plate between the left and right channels reduces crosstalk • Durable low resonance polymer housing Elliptical Nude Nude Round Shank Elliptical Bonded Bonded Round Shank VM530EN/H DUAL MOVING MAGNET STEREO CARTRIDGE WITH HEADSHELL VM520EB/H DUAL MOVING MAGNET STEREO CARTRIDGE WITH HEADSHELL Conical Bonded Bonded Round Shank 08 Product Information For Shellac or Phonograph Records Conical (3mil) Bonded Round Shank VM670SP DUAL MOVING MAGNET MONO CARTRIDGE Model dedicated to 78 rpm records, whose round stylus has a large curvature radius at the tip. The curvature radius is 3 mil, and suitable for playing 78 rpm records from a wide variety of eras. • Aluminium cantilever • Para-toroidal coils improve generating efficiency • Mono body terminating left and right channels reduces surface noise • Durable low resonance polymer housing For Mono Vinyl LP Records VM610MONO DUAL MOVING MAGNET MONO CARTRIDGE Mono LP model with a conical bonded stylus in the body dedicated to monaural sound. Specialised internal wiring allows for reduced surface noise and stable sound reproduction. • Aluminium cantilever • Para-toroidal coils improve generating efficiency • Mono body terminating left and right channels reduces surface noise • Durable low resonance polymer housing Conical Bonded Round Shank 09 Replacement & Upgrade Styli Even the finest diamond stylus becomes worn after an extended period of play. The styli in our VM cartridges are no different. But it is easy to replace the stylus and continue to use your cartridge. Our renewed VM cartridges have 7 styli and 3 types of bodies to choose from. Not only is it not necessary to buy an entirely new cartridge, but you can also enjoy the experience of upgrading your stylus or trying a new cartridge/stylus combination. Special Line Contact Stylus Shibata Stylus MicroLine® Stylus Elliptical Nude Stylus Elliptical Bonded Stylus Conical Bonded Stylus 3mil Conical Bonded Stylus CartridgeBody Product VMN60SLC VMN50SH VMN40ML VMN30EN VMN20EB VMN10CB VMN70SP *(1) *(1) *(1) *(1) *(1) *(1) *(1) Becomes VM670SP (1) Since SP records only have monaural modulation, combining an SP stylus with a stereo body would be recommended only when used with a dedicated archiving phono Preamplifier-equaliser. These incorporate various features to allow Mono reduction from Stereo inputs (Mono L+R, Mono L, Mono R, L&R Variable Mix). When an SP record is played with a standard Stereo Phono Preamplifier, it is recommended that a VM600 body is used for signal to noise ratio optimisation and to minimise record surface noise. (2) For best results when playing vintage mono LPs, Audio-Technica recommends using the VMN510CB conical stylus. A line contact or elliptical type stylus can be considered if you are sure that the dimensional groove construction of the LP(s) can safely handle these stylus tip shapes. * *Lifetime of the replacement stylus is approx. 300 to 500 hours for Conical, 300 hours for Elliptical, 1000 hours for MicroLine®, and 800 hours for Shibata and Special Line Contact. 10 VM760SLC Standard Replacement Becomes VM750SH Becomes VM740ML Compatible Compatible Compatible VM750SH Becomes VM760SLC Standard Replacement Becomes VM740ML Compatible Compatible Compatible VM700 Body VM740ML Becomes VM760SLC Becomes VM750SH Standard Replacement Standard Replacement Becomes VM540ML Compatible Compatible Compatible VM540ML Compatible Compatible Becomes VM530EN Becomes VM520EB Becomes VM510CB VM530EN Compatible Compatible Becomes VM540ML Standard Replacement Becomes VM520EB Becomes VM510CB VM500 Body VM520EB Compatible Compatible Upgrade to VM530EN Standard Replacement Becomes VM510CB VM510CB Compatible Compatible Becomes VM540ML Upgrade to VM530EN Upgrade to VM520EB Standard Replacement Standard Replacement VM670SP *(2) *(2) *(2) *(2) *(2) Becomes VM610MONO VM600 Body VM610MONO Compatible Compatible Compatible *(2) *(2) Standard Replacement Specifications VM760SLC TypeVM VM750SH VM 20 to 27,000Hz 4.0mV (1kHz, 5cm/sec.) 30dB (1kHz) 1.0dB (1kHz) 1.8 to 2.2g (2.0g standard) 2.7k ohms (1kHz) 800 ohms 47k ohms 100 to 200pF 460mH (1kHz) 40×10 -6 cm/dyne 10×10 -6 cm/dyne (100Hz) Nude Shibata (2.7×0.26mil) Aluminium tapered pipe 23° H17.3×W17.0×D28.2mm 8.0g VMN50SH Cartridge installation screws 5mm×2 and 10mm×2 Washer×2 Hexagon nut×2 Non-magnetic screwdriver×1 Brush×1 Leadwireset×1 VM530EN/H VM740ML VM 20 to 27,000Hz 4.0mV (1kHz, 5cm/sec.) 28dB (1kHz) 1.0dB (1kHz) 1.8 to 2.2g (2.0g standard) 2.7k ohms (1kHz) 800 ohms 47k ohms 100 to 200pF 460mH (1kHz) 40×10 -6 cm/dyne 10×10 -6 cm/dyne (100Hz) Nude MicroLine (2.2×0.12mil) Aluminium tapered pipe 23° H17.3×W17.0×D28.2mm 8.0g VMN40ML Cartridge installation screws 5mm×2 and 10mm×2 Washer×2 Hexagon nut×2 Non-magnetic screwdriver×1 Brush×1 Leadwireset×1 VM540ML VM 20 to 27,000Hz 4.0mV (1kHz, 5cm/sec.) 28dB (1kHz) 1.0dB (1kHz) 1.8 to 2.2g (2.0g standard) 2.7k ohms (1kHz) 800 ohms 47k ohms 100 to 200pF 460mH (1kHz) 40×10 -6 cm/dyne 10×10 -6 cm/dyne (100Hz) Nude MicroLine (2.2×0.12mil) Aluminium tapered pipe 23° H17.3×W17.0×D28.2mm 8.0g VMN40ML Cartridge installation screws 5mm×2 and 10mm×2 Washer×2 Hexagon nut×2 Non-magnetic screwdriver×1 Brush×1 Leadwireset×1 VM520EB/H H21.3×W21.0×D60.4mm 16.8g VM530EN VM 20 to 25,000Hz 4.5mV (1kHz, 5cm/sec.) 27dB (1kHz) 1.5dB (1kHz) 1.8 to 2.2g (2.0g standard) 2.7k ohms (1kHz) 800 ohms 47k ohms 100 to 200pF 460mH (1kHz) 35×10 -6 cm/dyne 8×10 -6 cm/dyne (100Hz) Nude elliptical (0.3×0.7mil) Aluminium pipe 23° H17.3×W17.0×D28.2mm 6.4g VMN30EN Cartridge installation screws 5mm×2 and 10mm×2 Washer×2 Hexagon nut×2 Non-magnetic screwdriver×1 Brush×1 – VM520EB VM 20 to 23,000Hz 4.5mV (1kHz, 5cm/sec.) 27dB (1kHz) 1.5dB (1kHz) 1.8 to 2.2g (2.0g standard) 2.7k ohms (1kHz) 800 ohms 47k ohms 100 to 200pF 460mH (1kHz) 35×10 -6 cm/dyne 8×10 -6 cm/dyne (100Hz) Bonded elliptical (0.3×0.7mil) Aluminium pipe 23° H17.3×W17.0×D28.2mm 6.4g VMN20EB Cartridge installation screws 5mm×2 and 10mm×2 Washer×2 Hexagon nut×2 – – – VM510CB VM 20 to 20,000Hz 5.0mV (1kHz, 5cm/sec.) 25dB (1kHz) 1.5dB (1kHz) 1.8 to 2.2g (2.0g standard) 2.7k ohms (1kHz) 800 ohms 47k ohms 100 to 200pF 460mH (1kHz) 35×10 -6 cm/dyne 8×10 -6 cm/dyne (100Hz) Bonded conical (0.6mil) Aluminium pipe 23° H17.3×W17.0×D28.2mm 6.4g VMN10CB Cartridge installation screws 5mm×2 and 10mm×2 Washer×2 Hexagon nut×2 – – – VM670SP VM 20 to 20,000Hz 3.0mV (1kHz, 5cm/sec.) – – 4.5 to 5.5g (5.0g standard) 1.4k ohms (1kHz) 400 ohms 47k ohms 100 to 200pF 230mH (1kHz) 15×10 -6 cm/dyne 2.0×10 -6 cm/dyne (100Hz) Bonded conical (3mil) Aluminium pipe 23° H17.3×W17.0×D28.2mm 6.4g VMN70SP Cartridge installation screws 5mm×2 and 10mm×2 Washer×2 Hexagon nut×2 – – – VM610MONO VM 20 to 20,000Hz 3.0mV (1kHz, 5cm/sec.) – – 1.8 to 2.2g (2.0g standard) 1.4k ohms (1kHz) 400 ohms 47k ohms 100 to 200pF 230mH (1kHz) 35×10 -6 cm/dyne 8×10 -6 cm/dyne (100Hz) Bonded conical (0.6mil) Aluminium pipe 23° H17.3×W17.0×D28.2mm 6.4g VMN10C Cartridge installation screws 5mm×2 and 10mm×2 Washer×2 Hexagon nut×2 – – – Frequency response Output voltage Channel separation Output balance Tracking force Coil impedance DC resistance Load impedance Load capacitance Coil inductance Static compliance Dynamic compliance Stylus Cantilever Vertical tracking angle Dimensions Weight Replacement stylus (sold separately)*» Accessories VM cartridges with Headshell Dimensions Weight 20 to 30,000Hz 4.0mV (1kHz, 5cm/sec.) 30dB (1kHz) 1.0dB (1kHz) 1.8 to 2.2g (2.0g standard) 2.7k ohms (1kHz) 800 ohms 47k ohms 100 to 200pF 460mH (1kHz) 40×10 -6 cm/dyne 10×10 -6 cm/dyne (100Hz) Nude Special Line Contact (1.5×0.28mil) Aluminium tapered pipe 23° H17.3×W17.0×D28.2mm 8.0g VMN60SLC Cartridge installation screws 5mm×2 and 10mm×2 Washer×2 Hexagon nut×2 Non-magnetic screwdriver×1 Brush×1 Leadwireset×1 VM540ML/H H21.3×W21.0×D60.4mm 16.8g *In this series, we offer replacement styli with different stylus tip structures and point shapes. For more details, please refer to «Replacement Stylus Lineup» on page 10. Specifications are subject to change without notice due to improvements. H21.3×W21.0×D60.4mm 16.8g 11 12 VS Audio-Technica Ltd . Technica House . 5 Millennium Way . Leeds LS11 5AL www.audio-technica.com Quote Link to comment Share on other sites More sharing options...
JohnJ Posted December 26, 2019 Share Posted December 26, 2019 @bkwa1959 thought yours was @dirtmudd s reply. Those are mostly newer mm's that you listed. Never seen an AT that looked like that with the side dimple. I got my first in the mid 80s at Sound Systems on South B. @joessportster, try sending that pic to AT USA . They might be of help. Quote Link to comment Share on other sites More sharing options...
dirtmudd Posted December 26, 2019 Share Posted December 26, 2019 3 hours ago, joessportster said: Any help appreciated, I know its Audio Technica but cant find the model !!!!!!!!!!!! Anyone ? 1 hour ago, JohnJ said: @bkwa1959 thought yours was @dirtmudd s reply. Those are mostly newer mm's that you listed. Never seen an AT that looked like that with the side dimple. I got my first in the mid 80s at Sound Systems on South B. @joessportster, try sending that pic to AT USA . They might be of help. It looks like the Signet audio technia.. https://www.vinylengine.com/library/signet/tk5e.shtml. https://www.canuckaudiomart.com/details/83145-four_vintage_cartridges_signet_tk5e__atn771e_shure_m91edstereo_voice_sv71s_no_styli/images/73622/ https://www.canuckaudiomart.com/details/649196465-nos-audio-technica-signet-tk7e-cartridge-and-genuine-nos-tkn2/images/966725/ https://www.canuckaudiomart.com/details/649196465-nos-audio-technica-signet-tk7e-cartridge-and-genuine-nos-tkn2/ 1 Quote Link to comment Share on other sites More sharing options...
JohnJ Posted December 26, 2019 Share Posted December 26, 2019 Good work @dirtmudd 1 Quote Link to comment Share on other sites More sharing options...
dirtmudd Posted December 26, 2019 Share Posted December 26, 2019 I forgot we need a vid.. Quote Link to comment Share on other sites More sharing options...
joessportster Posted December 26, 2019 Author Share Posted December 26, 2019 10 hours ago, dirtmudd said: It looks like the Signet audio technia.. https://www.vinylengine.com/library/signet/tk5e.shtml. https://www.canuckaudiomart.com/details/83145-four_vintage_cartridges_signet_tk5e__atn771e_shure_m91edstereo_voice_sv71s_no_styli/images/73622/ https://www.canuckaudiomart.com/details/649196465-nos-audio-technica-signet-tk7e-cartridge-and-genuine-nos-tkn2/images/966725/ https://www.canuckaudiomart.com/details/649196465-nos-audio-technica-signet-tk7e-cartridge-and-genuine-nos-tkn2/ Your the man Signet TK5e she is. Now I know the specs and can adjust setup though it sounds fine to me 1 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.