Guest " " Posted July 29, 2006 Share Posted July 29, 2006 Lets get the tools ready. Car jack under panel saw is helpful when cutting down a full sheet of 3/4 4X8 birch. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 Bench vise is helpful as a stop lock to preset for multiple exact cuts. Btw, the saw came with 8 rollers. I removed the rollers and put the 2 metal bars. The bars allows a better cut with less wood movement than what the rollers provided. Quote Link to comment Share on other sites More sharing options...
jwc Posted July 29, 2006 Share Posted July 29, 2006 So what's the plan? You gonna bring the woofer up 6 inches? Shorten the port? What woofer? What midhorn? Are you building this for yourself? If so....I would strongly suggest the Cornscala. Listening to them now. jc Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 Ok, here's the wood. We have 3 sheets of 3/4 inch 11 ply birch from home depot. We will add an additional panel made of 1/2 inch birch for the grills, this way you can remove the grills if you like. This birch has 2 grain patterns. A blonde side, and a darker lightly grained side. We will be using the blonde side. My 1980 unfinished birch LaScala's are blonde birch, and they look awesome. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 Will mark off the tops and side so when we assemble the cabs, the grain will flow in the correct matching direction. The bottom 16 inch horizontal section is scrap, with the exception of 2 pieces that will be used internally above the ports. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 Scrap section has been cut off. Btw, blade has been rotated 90 degrees into the horizontal cutting position. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 Horizontal cuts for the tops and sides have been completeted. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 We're ready to make the vertical cuts for th tops and sides. Blade will be rotated back into the vertical cutting position. In this position, the blade moves down on 2 tracks, the wood does not have to move. In the previous horizontal cutting position, the blade is locked into a cutting position, and the wood has to slide thru the cut. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 vertical cuts for the tops and sides have been completed. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 'Next peice of 4X8 birch is loaded on the panel saw. Lets mark the front and back panels for each cab, and make the cuts. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 Time to make the bottom sections. There is enough wood on the scrap section to cut both the bottoms and the internal baffle abve the ports, so we will use that. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 jwcullison Using the forum plans for a 3 port cornwall as well as a template that I have from an actual cornwall motorboard. Standard lay out using 3 ports. Yes, woofers will be rasied six inches. Modern Xover poits will be used. Woofer will be k-33 Mid will be k-55, on standard horn. No, not building for myself. Building for another forum member using the forum plans. Slight modifications to fit into a shipping box. When I get done with these, and get done with 2 LaScala refinsh projects, will start on Jubilee project. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 Main pieces cut. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 now we are going to change the blade on the panel saw and do finishing trim cuts on all the peices. We'll use the stop lock clamp to set all the vertical cuts, and then reset for all the horizontal cuts. All we will need to do is slide the wood in, and move the saw down the slidered. Very little sanding will be needed once this blade passes over the rough cuts. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 All vertical cuts get trimmed with the fine cutting blade. Notice the clamp stop. This makes all cuts the same lenth. We just move the wood into position. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 29, 2006 Share Posted July 29, 2006 All vertical cuts get trimmed with the fine cutting blade. Notice the clamp stop. This makes all cuts the same lenth. We just move the wood into position. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 30, 2006 Share Posted July 30, 2006 All horizontal cuts get trimmed with fine blade. Stop clamp moved into new position for all the pieces. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 30, 2006 Share Posted July 30, 2006 When using the fine trim blade to do polishing cuts, I makr the edges with dots to keep track of whats needs to be cut. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 30, 2006 Share Posted July 30, 2006 Ready to do an intial assembly of cabinet B. Only a small amount of glue is needed. We will put in 1X2 bracing on all corners as well as the fronts and backs later. Quote Link to comment Share on other sites More sharing options...
Guest " " Posted July 30, 2006 Share Posted July 30, 2006 Ok, clamps are in their general positions. Time to move the cab abd reposition bottom clamps 90 degrees for max clamping pressure. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.