JL Sargent Posted June 17, 2011 Share Posted June 17, 2011 Found an old console at the thriftstore for a paultry sum and brought it home. Inside was this sweet little tube amp from Stromberg Carlton. I installed new RCAs, Binding posts, switch, and ON indicator, only to find one channel was AOL. After some hunting I found a 33K ohm resister that measured a whopping 8 Meg. Replaced that and all is well. This amp uses a compliment of four 7408 tubes which I understand is an uprated version of the 6V6GT along with two 7199s. Anyway just thought I would share this little project amp. Quote Link to comment Share on other sites More sharing options...
Boxx Posted June 17, 2011 Share Posted June 17, 2011 What a great find and upgrade! How do you plan to use it? Quote Link to comment Share on other sites More sharing options...
JL Sargent Posted June 17, 2011 Author Share Posted June 17, 2011 I've got just a little bit more work to do first. I'm replacing all the coupling caps (Eight .05uf and two .0047uf Orange Drops going in). Then I'll be using it with a HD tuner (bought from Jhoak here on the forum) for my office listening. Should work out real well for me as the tuner has a volume control and a remote! Quote Link to comment Share on other sites More sharing options...
NOSValves Posted June 17, 2011 Share Posted June 17, 2011 If you're handy with a soldering iron I'd suggest swapping out those output transformers with something better and then doing some mild tweaking of the circuit. If you are interested and have a schematic of the circuit I could cook something up for you. Quote Link to comment Share on other sites More sharing options...
JL Sargent Posted June 17, 2011 Author Share Posted June 17, 2011 Hey Craig, any and all input from you welcome! Here is the amp under the hood. I swapped that top cap hunting for my problem! Quote Link to comment Share on other sites More sharing options...
NOSValves Posted June 18, 2011 Share Posted June 18, 2011 Nice picture! But I need an actual schematic to help tweak it. If your not sure what a schematic is then we may not want to mess with the amp. It's an electrical road map of the circuit listing the values of all the components in the circuit input to output. It may also have voltage specifications. Quote Link to comment Share on other sites More sharing options...
JL Sargent Posted June 18, 2011 Author Share Posted June 18, 2011 Wow, found the correct one! Thanks for the help Craig. Oh, and well versed on schematics, 8 years electronics tech USAF. Quote Link to comment Share on other sites More sharing options...
NOSValves Posted June 18, 2011 Share Posted June 18, 2011 Cool that makes helping you a bunch easier both with the scat and your experience! Do a couple confirmation measurements for me. Measure the wall voltage the amp is running at first. measure pins 3, 4 and 8 of one of the 7408 output tubes. this amp will be dead simple to modify for better output iron. If you look at the output transformer specs you should be able to see why it will be handicapped achieving full balanced frequency response across a broad range while driving a full range speaker like Klipsch. Quote Link to comment Share on other sites More sharing options...
JL Sargent Posted June 18, 2011 Author Share Posted June 18, 2011 Here is what I have. Pins 3 to 8 = 331v 4 to 8 = 311v 3 to 4 = 20.6v Quote Link to comment Share on other sites More sharing options...
mike stehr Posted June 18, 2011 Share Posted June 18, 2011 The cathode biasing looks quite similar to what Magnavox did. Quasi-cathode bias, tied in with the heater winding through the two 47 ohm resistors. Do you have feedback network connected? There should be a 68K (with a .01 uF cap in series on some models) resistor from the cathode of the input section of the 7199, to the secondary of the output transformer. (green wire) Quote Link to comment Share on other sites More sharing options...
JL Sargent Posted June 18, 2011 Author Share Posted June 18, 2011 Do you have feedback network connected? There should be a 68K (with a .01 uF cap in series on some models) resistor from the cathode of the input section of the 7199, to the secondary of the output transformer. (green wire) You know, there it is plain as day in the schematic but I can tell you that circuit was not in this amp when I pulled it. The Tranny outputs were on top of the amp and went to the speakers only. Any thoughts on the difference?? Quote Link to comment Share on other sites More sharing options...
mike stehr Posted June 18, 2011 Share Posted June 18, 2011 Do you have feedback network connected? There should be a 68K (with a .01 uF cap in series on some models) resistor from the cathode of the input section of the 7199, to the secondary of the output transformer. (green wire) You know, there it is plain as day in the schematic but I can tell you that circuit was not in this amp when I pulled it. The Tranny outputs were on top of the amp and went to the speakers only. Any thoughts on the difference?? Well, without feedback the amp could have a bit more noise, and a bit shouty with a more accentuated midrange response. The turret board in the underside pic of the amplifier shows a couple 68K resistors, (blue/gray/orange) maybe that's the feedback resistor. See if if they are disconnected. If they are, maybe try it with the feedback connected, and disconnected to see which sounds best. Quote Link to comment Share on other sites More sharing options...
jhoak Posted June 18, 2011 Share Posted June 18, 2011 What a GREAT find. Major kudos to you for bringing a piece of old techonolgy back to a useful state. I keep thinking that I'll stumble across something like that at some point. About a bazillion years ago when the world was young I worked just up the street from a Stromberg Carlson R&D facility. At the time I managed a Radio Shack store. That particular store was like the number 2 or 3 in the country for "parts" only sales because of the engineers at S/C. They were in so often that I got to be pretty good friends with a few of them. I was always amazed at some of the S/C tubed audio kit that most of them listened to. They were all like "MEH" about their systems. At the time I would have KILLED for what they were listening to. bought from Jhoak here on the forum OK... I really don't want to wizz in your Cheerios but don't get too cranked up about that tuner. The internal DACs aren't what I would call "all that". Not horrid but just not very good. I always used it piped in by way of a coaxial connection to an Emotiva DAC. On the few occasions that I used the internal processing I wasn't very impressed. All of that is to say that when you get it all hooked up and you're disappointed with what you're hearing it is NOT the amp or the speakers it's the tuner. Pick up pretty much any low $$ DAC and you'll hear an immediate improvement. Quote Link to comment Share on other sites More sharing options...
JL Sargent Posted June 18, 2011 Author Share Posted June 18, 2011 OK Jhoak, no big deal. Mike, After lifting that board I can see that the feedback circuit is actually wired through those 68K resistors as you suspected. I had to think about it because these transformers have dual secondary wires. A pair out the top and a pair out the bottom. Quote Link to comment Share on other sites More sharing options...
NOSValves Posted June 19, 2011 Share Posted June 19, 2011 Here is what I have. Pins 3 to 8 = 331v 4 to 8 = 311v 3 to 4 = 20.6v Measure again from circuit ground to pin's 3, 4 & 8 I also need to know what the AC wall voltage is at when making these measurements. Quote Link to comment Share on other sites More sharing options...
JL Sargent Posted June 19, 2011 Author Share Posted June 19, 2011 OK, Pin 3 - 348v Pin 4 - 330v Pin 8 - 21v Power distribution block amp is plugged into measures 120.6v with amp working. Quote Link to comment Share on other sites More sharing options...
JL Sargent Posted June 20, 2011 Author Share Posted June 20, 2011 For reference found this info on 7408 power tube: ampagetube data ampagetube data 7408BEAM POWER TUBE Pin Element 1 none 2 Heater (Filament) 3 Plate (Anode) 4 Screen Grid 5 Control Grid 6 none 7 Heater (Filament) 8 Cathode Glass octal type usedas output amplifiertube in high-qualitysound systems.Tubes require octalsocket and may bemounted in any position. Heater Voltage (AC/DC) 6.3 volts Heater Current 0.45 ampere Heater Warm-up Time (Average) 11 seconds Heater-Cathode Voltage Average Peak Heater negative with respect to cathode 100 max 200 max volts Heater positive with respect to cathode 100 max 200 max Direct Interelectrode Capacitance (Approx.) Grid No.1 to Plate 0.7 pf Grid No.1 to Cathode, Heater, Grid No.2, and Grid No.3 9 Plate to Cathode, Heater, Grid Ho.2, and Grid No.3 7.5 CLASS A1 AMPLIFIER Maximum Ratings (Design-Maximum Values) Plate Voltage 350 max volts Grid-No.2 (Screen-Grid) Voltage 315 max Plate Dissipation 14 max watts Grid-No.2 Input 2.2 max Typical Operation and Characteristics Plate Voltage 60 250 volts Grid-No.2 Voltage 250 250 Grid-No.1 (Control-Grid) Voltage 0 -12.5 Peak AF Grid-No.1 Voltage - 12.5 Zero-Signal Plate Current 100 45 ma Maximum-Signal Plate Current - 47 Zero-Signal Grid-No.2 Current 22 4.5 Maximum-Signal Grid-No.2 Current - 7 Plate Resistance (Approx.) - 50000 ohms Transconductance - 4100 umhos Load Resistance - 5000 ohms Total Harmonic Distortion - 7 % Maximum-Signal Power Output - 4.5 watts Maximum Circuit Values Grid No. 1 Circuit Resistance For fixed-bias operation 0.1 max megohm For cathode-bias operation 0.5 max Quote Link to comment Share on other sites More sharing options...
Tractrix Posted June 21, 2011 Share Posted June 21, 2011 I would make sure that the following resistors were matched: R47:R48 R45:R46 R55:R56 R53:R54 R61:R62 Also, because the line voltage has changed since this amp was built, going from 110 to 120VAC, you now have too much voltage on the output tube plates. These tubes are going to run hotter than intended. You may have to adjust R58 to bring the DC voltage down. Otherwise, without changing the input and driver stages, there's not much to do that has not already been said. Quote Link to comment Share on other sites More sharing options...
NOSValves Posted June 21, 2011 Share Posted June 21, 2011 Okay here are my thoughts but in the end we will have to tweak it after parts are installed. I'd use a set of hammond 1650F output transformers (hopefully they can be shoehorned on the existing chassis). there are others that will work but with Hammond transformers or anything similar you are way better off going overboard then just up to spec if Sonics is your goal. I'd change R63 to about 200 Ohms 10 watt. This will help cool down the current to the 4 7408 output tubes a bit. The 348 volts on the plates is within max spec and you also have to deduct the cathode voltage from the plate for effective plate voltage. I would change R59 to correct the voltages for the 7199 driver/phase inverter. I bet a 5.6K or 6.8K 10 watt will do a fine job at that. I'd replace C55, C56, C60 and C61 with .1 uf 400 V caps 1'd replace R47, R48, R55 and R56 with 120K 1/2 watt minimum rating. Then since this amp is so simple and laid out to be easily worked on I'd replace every single component at stock value. For resistors I'd stick with Carbon types carbon film will do just fine. The matching to within 2% of the above mentioned resistors (by tractrix) is a real good idea for best performance. I'd absolutely replace C52 multi section filter cap and up the UF value best as possible on all 3 sections. The feedback network will most likely need a bit of tweaking but the real problem with that is we need a function generator and a scope to tune that circuit to the new transformers. If need be you can ship it over I can perform that last step if we feel the need. Hey maybe you have a function generator and scope for all I know? Quote Link to comment Share on other sites More sharing options...
JL Sargent Posted June 21, 2011 Author Share Posted June 21, 2011 Alright, I'm on it! Man, I'm gonna have something when this is done. I notice that Parts Express has those transformersI Is there a better source? Craig, are Orange Drops 600v good on the .1 caps or do you suggest another? On the sectoral cap, how much higher on the UH can/should I go? Who is a source for those? I do have a scope, maybe I can pick up a function gen. Craig, thanks again for the help with this, I'm excited about it. Tractrix, I appreciate your suggestions also. I'll be working on my parts order together tonight. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.