Klipsch Pro Audio
Talk about our Pro Audio and Cinema products here.
1226 topics in this forum
-
- 0 replies
- 291 views
-
- 0 replies
- 334 views
-
- 0 replies
- 313 views
-
- 0 replies
- 461 views
-
- 0 replies
- 362 views
-
- 0 replies
- 329 views
-
- 0 replies
- 409 views
-
- 0 replies
- 775 views
-
- 0 replies
- 443 views
-
- 0 replies
- 328 views
-
- 0 replies
- 285 views
-
- 0 replies
- 464 views
-
- 0 replies
- 355 views
-
- 0 replies
- 471 views
-
- 0 replies
- 434 views
-
- 0 replies
- 367 views
-
- 0 replies
- 866 views
-
- 0 replies
- 569 views
-
- 0 replies
- 267 views
-
- 0 replies
- 272 views
-
- 0 replies
- 368 views
-
- 0 replies
- 318 views
-
- 0 replies
- 318 views
-
- 0 replies
- 326 views
-
- 0 replies
- 663 views
-
Recent Posts
-
By M_Klipsches · Posted
This is the T18 build. They are great projects, if you are reasonably handy.Buy the plans & follow Bill’s instructions to the letter and you’ll get good results. If you decide to go this route,there are some folks here that are ace builders, and great resources. Good luck, I’m happy to offer any advice that I can. https://community.klipsch.com/index.php?/topic/182249-t18-subwoofer-project/ -
By Woofers and Tweeters · Posted
Okay, I am going to have to get my ST70 in the queue. I have an Audio Research SP8 preamp that might go well with it. @Audio Flynn, do you still have your Audio Research SP12? -
By Woofers and Tweeters · Posted
What? I didn't ask, but I am trying to understand what point you're trying to make. Typically, you go against what I say. Are you, again, trying to correct me? I am not sure if you're catching on to bantering between Michael and Eric. They are a part of a small group who have audio gatherings. I don't know the head count for the Pilgrimage in 2018 or 2019, but it was only getting larger yearly. After the Covid lockdown was lifted, everyone was ready to get out and that would have been a record-setting attendance, if there wasn't the squabble that resulted in the departure of so many members. -
By M_Klipsches · Posted
I found the thread, for my Table Tuba build. It turned into my “Pandemic Project, as I’d just finished gathering parts before the world shut down. it documents the whole build. -
By Ole Dollar · Posted
Thanks for the tip, I did some research as I had not heard of that brand. Will order a quad to check them our when current tubes die. -
By M_Klipsches · Posted
Actually, I’ve documented the two I’ve built in threads on this forum. I’ll find the links to those threads. Here’s a pic of the one that probably would suit your Heresys fairly well, it’s the T18. -
If you haven't already done it replace the other one now. Then you're set for another eon. lol -
Thank you for the answer... thankfully, all is working the additions I like for the most part... If the wood is intact still beneath the front carving, I may remove that and restain it... Many thanks! Regards, Richard -
-
Just wanted to update everyone who helped out with this thread! I was able to replace the gasket on the midrange drive and the distortion is gone! Thanks to the group for their input! GS
-