rigma

Interesting read on the speakers John mentioned above. http://www.jblpro.com/PD5000/PDF/CMCD_TechNote.pdf

Thanks AL & Wolfram, I am working on the mounting baffle as we speak! Rigma

Al Klappenberger, I have your crossovers in my Khorns and have JBL 2404H tweeters I would like to use in this setup. Is there anything I need to do to the crossover to use these tweeters? Rigma

Here is where I buy my sleeves. They have a good variety and good service. http://www.sleevetown.com/lp-sleeves-inner.shtml MB

---------------- On 3/24/2004 6:49:08 PM IB Slammin wrote: ---------------- On 3/24/2004 5:22:28 PM rigma wrote: I have some Crown amps in very good condition that I would sell, DC-75 & DC-150 Series II. Make reasonable offer. mb ---------------- mb, is it DC-75, DC-150.....or D-75 and D-150????? Regards, Terry ---------------- Sorry they are D-75 and a D-150A Series II, I have 2 of each. mb

I have some Crown amps in very good condition that I would sell, DC-75 & DC-150 Series II. Make reasonable offer. mb

Here is the schematic for the Brook 12a. I don't remember where I got it. Hope this helps. mb

I have noticed on some Lp's my Sub Woofer seems to oscillate continuously but on others it is fine, it is definitely dependent on the particular Lp. Is this rumble and how can I control it? mb

mandi, I have one Imperials "One More Song For You" Produced in 1979. Condition is very good. Rigma

Many are virgin, never been opened and played with. Rigma

I have a good many of these LP's all in very good condition, many still sealed and unplayed. Most are contemporary Christian music. I would like to know if there is an interest by forum members. If there is enough interest here I will catalogue them an offer here prior to ebay. Rigma

John Warren, I sent you email & PM. Rigma

Any suggestions for a low cost Multi Channel SACD. I have a nice sounding Sony S9000ES SACD/DVD. Just want to try multi channel but don't want to spend much until I see if I like multi. Rigma

gerbache, I am in Lebanon about 20 mi east of Nashville.

gerbache, Where in TN do you live? I am near Nashville and have several tube and SS amps powering Klipschorns and LaScalla's. If you are close, I would be glad to have you over.

Jordon, Try this link to check seller contact info. http://cgi3.ebay.com/aw-cgi/eBayISAPI.dll?UserInformationRequest

I added spikes to my LaScalas. What I found to work is have speaker placement where you want without the spikes installed, then carefully tilt the LaScala forward and lay front on floor install spikes and tilt back up. That will put them back in the origanal place.

I will take the other copy if it is not spoken for. MB

Graig, What did you tell me the bias voltage on my MK-III was. Remember I have the Triode boards with 10 ohm bias resistor. MB

PIRANHA, Yes, I use the Scott LC-21, very similar to the Scott 130 with the MK-III

I use a Scott LC-21 pre and like the sound very much. MB

TBCooper, I have a set of LaScala plans and will make a copy and trade for a copy of your Speaker Lab KHorn plans. I built the Speaker Lab KHorns about 20 years ago, but since lost the plans, and would advise the same about wood glue instead of Silicon. I did apply a bead of Silicon to all joints after the glue dried. I also recently upgraded to AL K's crossovers which I built from his plans, well worth it. Also I feel you must have access to a good table saw to make some of the complex cuts! MB

Allan, I just sent you PM & email. MB

Guy, The mod is complete and works great, but it was much more difficult than expected. The motor I ordered was supposed to have the same shaft dia. as the VPI but was undersize so I had to make a bushing to adapt, also had to retap screw holes, etc.. Bottom line is I have to do more research to find a more compatible motor to make a kit economically feasible. I will keep the forum informed. MB

Chris, Were do you buy your Vinyl?