Jump to content
The Klipsch Audio Community

jason str

  • Content Count

  • Joined

  • Days Won


Everything posted by jason str

  1. Experience it for yourself, take some time and do some comparisons in strength & durability then get back to us. Take a video if need be to prove me wrong.
  2. I have repaired a few and threw out others not worth while. Lets not pretend it doesn't happen. My first set of speakers ( Jensen LS something) one of them fell and smashed in the whole corner and busted the seams and that was landing on 3/4" ply flooring with carpet on top.
  3. These are 30" x 30" x 24" wide, loaded W- 2x10" Eminence drivers. Other pro stuff as well. No affiliation. >link<
  4. It would be best to now maybe look into one of the KPT series if anything, sell those woofers and you have a great start. The THT's will sing right along with any KPT series as well. Many underestimate the Table Tuba because they think an 8 or 10" driver is not capable of performing well, that is until they hear one.
  5. I have mine at the same settings (-2dB) with my "A-4500". The only problem with my set and others is the driver is too large and it hits the top of the (La Scala) cabinet so it needs a bit of the cabinet ground down to fit flush.
  6. The proper tool for the job is best. People are probably looking for these woofers as well, sell them a get some proper drivers for the task at hand. Heads up. N/A.
  7. Dimensional lumber front to back is exactly how Klipsch updated the newer Cornwall series cabinets, that is the cabinets weak spot.
  8. Clean the area with a soap/watered damp cloth, let it completely dry. Apply a little shoe goo to the area carefully avoiding the curved surround with a toothpick until its sealed, let it cure at least 24 hours. A few thin coats is better than a one thick bead, removing the woofer(s) before repair will be easiest.
  9. Absolutely, looks unprofessional and lowers the resale value.
  10. Added weight and an unsatisfactory look. Measure from motorboard to flange face, this will be 2x4 brace length. Glue brace to motorboard between the woofer & squawker, set in place with glue and let dry. If you are worried about exact placement you can remove the squawker or woofer and test fit the new brace using a pencil to mark placement before anything else. This step will make drilling the rear panel hole placement easy. Simply drill the holes in the rear panel slightly larger than the screws to avoid binding on the plywood. I don't own Cornwalls ( so no measurements) just make sure to avoid brace placement under the rear jack.
  11. Run a 2x4 or two front to back. Just use glue to attach to the motorboard, let it dry and then screws through the rear panel.
  12. Just look down the end of the lumber, any crown goes up. Never had an issue either, any warped lumber was used up building headers or ripped down for other uses.
  13. Experienced cabinet builders use void free panels & any warping will straighten with the construction of the cabinet, MDF & HDF are cheaper subpar alternatives. Just recently they tore down the little brick ranch next door and put up this monstrosity of newly built house, all MDF and OSB construction and asked the guys building the place why they used those materials and the answer was dimensional lumber is never exactly straight. My thoughts afterwards was this place will fall apart before the old one would have.
  14. You will find that stacking takes the magic out of the music. The MCM1900 system is in a whole different league than La Scala's.
  15. I would use a bit of PEQ before porting personally to get that last bit of bass out but ultimately a proper horn loaded sub would be worlds better than either.
  16. https://billfitzmaurice.info/THT.html Cross it over @ 90 Hz or so to the La Scala's.
  17. jason str

    RIP Ric Ocasek

    Dad got me into The Cars with his Candy O album, good stuff. Dam shame Ric is gone.
  18. https://www.klipsch.com/products/kl-6504-thx-in-wall-speaker Download the manual.
  19. Been getting calls lately with our own name and number on the caller ID when normally its just been some schmuck who claims to be from Microsoft who tells me my computer license has expired spiel. I was on the phone trying to waste as much of the guys time as possible last week from one of those Microsoft Guru's until i mentioned i have only Apple systems (hung up on me quickly after) when now this week Apple computers calls and mentions my system needs maintenance. Good fun for a while but its starting to get old quickly.
  20. No, there was minimal foam to begin with. If i recall that foam pad was U shaped on the bottom of the cabinet, it was probably moved to install the crossover there. Nothing to worry about.
  21. Unhook it and lay a large towel on the floor and prop it up at a 45 degree angle and try again as the gasket may have gummed up over the years.
  • Create New...