NBPK402

How is a k402 3 times the size of a danley sh50? Sent from my SM-T830 using Tapatalk

From what I have read...all cartridges are actually balanced, it is just most are wired unbalanced. I like balanced, but I did not get into rewiring mine for balanced. If I end up down the road getting a higher end table I will look more into getting one with balanced wiring. Sent from my SM-T830 using Tapatalk

I would like to try that, if I can get a tapped horn that would put a 2'x2' horn on top and have the correct listening height. Sent from my SM-T830 using Tapatalk

SOLD Sent from my SM-T830 using Tapatalk

How ironic... I was in the USAF at RAF Alconbury from 1978 to 1981, and I was offered a job as the rep for the UK, for Nakamichi, and Yamaha. I Turner it down because I was enlisted, and with varying shifts I did not think I could do the job...now I with I would have accepted the offer. Sent from my SM-G985F using Tapatalk

I now have the Minidsp DDRC88A crossover/Dirac in place for my front 3 channels, and have the crossover settings transferred. I still need to install jacks on the rear of each speaker cabinet for the AmpCamp speaker hookups, and rewire the speakers internally. I am going to use banana jacks for the ACAs as it will avoid confusion down the road. On my left and right channels I am planning on putting the appropriate AmpCamp amp on top of each speaker... I am hoping it will not pass too much heat below the amp to the speaker cabinet as it is veneered. I will use the 4 wire Speakons for driving each woofer with its own amp. Sent from my SM-T830 using Tapatalk

Sometimes its cheaper to keep them...my last divorce cost me over $100k. Sent from my SM-T830 using Tapatalk

My MEHs are not as big as your Jubilees, but my wife did not like the big horn look at all. I made some black grills for mine and now she doesnt complain anymore about them. Sent from my SM-T830 using Tapatalk

I was wondering when someone would make some mumps. Did you notice a difference with your mumps? How did you make and install them? Sent from my SM-T830 using Tapatalk

Are the drivers all about the same depth? I have the EV DH1As, and was wondering if others are deeper insize. Sent from my SM-T830 using Tapatalk

I picked up a Pioneer player for about a $100, as I recall. Mine also rips SACDs with a modified firmware. Sent from my SM-T830 using Tapatalk

1978 la scalas purchased new in 78 Kp3002s Used Lascalas Hips K402s Sent from my SM-T830 using Tapatalk

I have a loft about 8' behind the mlp. Sent from my SM-T830 using Tapatalk

I am getting the 2 ddrc88ms for Dirac, and also to replace the Xilica...Chris Said they should be fine. I used the same models before when I had my JBLS and I never heard any difference when I moved to the Xilica. The 2x2 mehs will be for my surrounds...unless they sound as good as the current mehs, then they will move to the front. If they are moved to the front, I will be looking at building a pair of subs to go under them. Sent from my SM-T830 using Tapatalk

I will be doing some upgrading over the next few months... Ordered: 2 Minidsp ddrc88ms 3 Pass ACA stereo/mono amps Diy projects: 2 2' x 2' MEHs modeled from the small side of my MEHs. These will use the same drivers, but the horn will be made of MDF. Selling: 4 Klipsch rp160Ms Musical Fidelity MX VYNL phono preamp Yamaha CXA 5100 preamp Xilica xp4080 crossover Some Icepower asx20btl, and asx125SE/BTL amp modules Dune HD PRO 4K PLUS media player Sent from my SM-T830 using Tapatalk

I thought my EV DH1As were massive! Sent from my SM-T830 using Tapatalk

I run Speakons...I use a 4 wire one for my 2 way active and they make a 8 wire one for a 4 way. They are super simple to hookup and disconnect, but a bit of a pain to wire as a 4 way. Sent from my SM-T830 using Tapatalk

That is what I need for my MEHs. I wish I could get a flatpack still or some plans... I know where I can get some CNC work done if I had the plans. Sent from my SM-T830 using Tapatalk

What sub Is that under the belle? Sent from my SM-T830 using Tapatalk

I will be more than happy with my MEHs. Sent from my SM-T830 using Tapatalk

My friend built a shed in his back yard...I think it is 10x12, and he has a HT in it with 3 LaScalas. His setup sohnds great too. Sent from my SM-T830 using Tapatalk

You might even be able to solder or braze the pins on....it would be like a name tag plate is. You might even be able to get some thin nameplares and use some kind of glue and just glue it to the plates...it might be easier if you can find name plates thin enough. Sent from my SM-T830 using Tapatalk

Have you thought about gluing some pieces of metal like for earings...then just push through the grill and put little earing clasps on it to secure. By doing it this way you do not damage the grills other than 1 or 2 small holes. Sent from my SM-T830 using Tapatalk

I am debating on absorption panels below 12' and poly diffuser panels 12' to 16' not sure if that will work or not. I think I still have 3 boxes of Roxul r60 2" left. Sent from my SM-G985F using Tapatalk

I am loving them more everyday...best horn speakers I have ever owned. I still need to get some more acoustic panels made though to get the echo down. Sounds like a night club when I turn it up, but at lower level the echo is not as bass LOL Sent from my SM-G985F using Tapatalk