Jump to content
The Klipsch Audio Community
babadono

Light bulb current limiter

Recommended Posts

Hi Guys,

Esoecially you who build/modify amps....

Do you just wire a light bulb in series with the AC hot line if you're fearing your build or mod might cause an input power problem?

 What wattage? I posted over in the solid state section about a mod I'm doing but thought I might try here and get more exposure.

Thanks in advance

Share this post


Link to post
Share on other sites
Posted (edited)

It's my understanding that limiting turn-on current is primarily a tube amp repair/restoration tool. The issue there is old capacitors that turn into resistors and fry tubes if switched directly to 120V after decades of of sitting in a closet. In that case techs generally use a variac and slowly ramp up voltage - but even that can result in damage to a tube amp - thus the light bulb limiter.

 

I ran a concert production company, that means we supplied "backline", a term for rented musical equipment. This allowed musicians to travel lighter and specify certain tubed guitar amps, etc. be supplied by the promoter. Thus I became versed in tube equipment. Thus I built what you're asking about (though I still don't know if it reasonably applies to non-tube stuff).

 

The deal with the light bulb in series with the tube amp is that if it got bright, capacitors had failed and needed attention, but given that the bulb when bright increases wildly in resistance, not enough current passed to damage the tubes and other stuff that wasn't broken. If the bulb was dim, the caps were probably fine. You add a switch to short the bulb once the amp started OK so that the full 120V is then supplied.

 

A simple version. I found that a 200W bulb was required to pass enough voltage to the DUT:

 

LampBox.thumb.JPG.2fb89ad55c542f5f83b27ecdb14ce11c.JPG

 

Rocket Science Schematic:

574041424_LampBoxSchematic.thumb.png.d71000fc8eb870bcd41714103ee7be16.png

Note: be sure the ground passes from male to female Edisons (that's the correct term for the 120V 3-wire plugs we use in America). : )

 

God bless you and your precious family - Langston

Edited by Langston
  • Like 1

Share this post


Link to post
Share on other sites

Thanks @Langston. Pretty much what I thought. Just wire the bulb in series with the hot. Wattage is probably determined by the max. the amp is supposed to draw I would think. There used to be member here and other audio forums @djk who was an absolute master and godsend with these kind of questions. Sadly he passed  few years back. R.I.P.

Share this post


Link to post
Share on other sites
Posted (edited)

I just looked through some of @djk 's posts. He truly was a master. : )

 

This forum is gaining a lot of respect from me. I'm impressed with the respect I see between different posters, particularly the knowledgeable toward the newbies.

 

Blessings - Langston

Edited by Langston
  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites
3 hours ago, Langston said:

I just looked through some of @djk 's posts. He truly was a master. : )

 

This forum is gaining a lot of respect from me. I'm impressed with the respect I see between different posters, particularly the knowledgeable toward the newbies.

 

Blessings - Langston

He helped alot of people. Not very long ago helped a member with problems in Belgium with a concert using LaScalas for out of doors venue.

  • Like 1

Share this post


Link to post
Share on other sites

100 watt old type bulb for SS, 300 watt old type bulb for tube gear. Recommended to me and what I use building and testing. Use bub limiter more than my variac. Sometime use both depending on application.

  • Like 1

Share this post


Link to post
Share on other sites
On 6/9/2021 at 5:49 PM, Langston said:

just looked through some of @djk 's posts. He truly was a master. : )

He educated me on the matter, I believe it was his primary tool for firing up old components.  

Share this post


Link to post
Share on other sites

I don't need a current limiter.  Just pointing out that it's now hard to find incandescent bulbs any brighter than 60 watts.  Do you get these brighter bulbs from specialty dealers?  I could use a 150-watt bulb for one of my studio flashes.

Share this post


Link to post
Share on other sites

They are available in a specialized field but right now I cannot remember what or where. Do some google searching and I am sure you will be able to find them. The only use for a current limiter are technicians and builders of amplifiers. If there is a dead short somewhere the build will light up drawing current away from device.  If you do neither no need to have or build one. 

 

With a variac you slowly increase the voltage while monitoring amps with an amp meter. If amperage rises very high you immediately know there is a problem and can quickly shut it down. 

Share this post


Link to post
Share on other sites

 

1 hour ago, henry4841 said:

With a variac you slowly increase the voltage while monitoring amps with an amp meter. If amperage rises very high you immediately know there is a problem and can quickly shut it down. 

And you can install a 1A fast or slow blow fuse in the Variac to limit current draw regardless of what the Amp meter shows.  Regarding the amp meter, I use a Fluke that measures in mA AC.  Most tube amps idle at about 1000-2000mA.  I have a dedicated VAC meter on the setup as well.

 

 

 

  • Like 1

Share this post


Link to post
Share on other sites
On 6/9/2021 at 6:36 PM, babadono said:

 @djkwho was an absolute master and godsend with these kind of questions. Sadly he passed  few years back. R.I.P.

I did not know that @djk  passed away , his last post was Jan 26 2018 so going on 3,5 years

Share this post


Link to post
Share on other sites
8 hours ago, John Warren said:

 

And you can install a 1A fast or slow blow fuse in the Variac to limit current draw regardless of what the Amp meter shows.  Regarding the amp meter, I use a Fluke that measures in mA AC.  Most tube amps idle at about 1000-2000mA.  I have a dedicated VAC meter on the setup as well.

 

 

 

image.png.9435484f530e2abab44961b4cb297a07.png

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...