Turbox

yeah that's what I was going to say where is Thebes when you need him. I never really did like the beetles...a bit before my time.

these aren't far from my place there...about 10 minutes.

Hi there, and welcome. I had Cornwall II's for about 20 years before I sold them off and they were really great for sure. Im not sure they are quite up to the task of the Khorns but to be completely honest. I have never owned Khorns. Were you not expecting them to be as good as they were?

oh great, now I got the itch

I do agree with being able to bypass the amp and be able run them with another input, something which goes through a passive.

Still looking for another pair of K69A's.

now were talking

everything is relative, but yes its a great sub.

donation has been made. Thanks again for doing this.

Absolutely terrible news. RIP.

I cant say enough about my Jubilee's. they are just amazing. I have little desire to upgrade beyond them.

I finished my extra wide F20. I decided to go with 24 inches, in total is 25.5 inches with the sides on. This thing is pretty amazing. Its not painted or finished yet.

maybe a bit high on the 1133's.

Looking for a few, PM me and let me know what you have?

Well, all I can say is I feel your pain...know exactly how you feel. It so cold here, there are icicles hanging from...never mind...

Im using the Dayton Audio RSS390HF-4 15" Reference HF Subwoofer 4 Ohm as well. I stole the idea from a build Carl did. im exepcting good things from this sub. My F20 is 25.5 inches wide and is almost done. I sealed up the cabinet earlier today. Its a fairly easy build, took me about 4 days from start to sealed up. I tell ya. that PL premium is nasty stuff.

so, I've started my F20 build. which is really 18.5 inches width. 3/4 inch ply on each side brings the width to 20 inches, hence the F20. In another thread we were discussing potentially bringing the width of the F20 to either 24 or even 30 inches. this would allow a better and more efficient response at the lower end of Fc low. So I've started my build. I've decided to build an f25.5 if I can call it that. 24 inches inside horn width, with 3/4 inch ply on each side. F25.5. I decided on using 24 inches rather than 30, because that is the most efficient use of three sheets of plywood. a 30 inch unit would have left me with to much wastage. I am using the Dayton Audio RSS390HF-4 15" Reference HF Subwoofer 4 Ohm. One of the baddest @ss woofers I've seen in a long time. I bought two of these a while ago for a dual F20 build. which might turn into a dual F25.5 build. Its a pretty easy build really, just takes some time, that's all. and im not in a rush. I ran all the plywood through the table saw to get everything the same width. so no issues there. My question is, with the wider width, could I have used Dayton Audio RSS460HO-4 18" Reference HO Subwoofer 4 ohm and been able to get a better response? 18 inch rather than a 15 inch. Theres no turning back now, but i would figure that the 18 inch driver might give a better response? and move more air?

did I miss something?

Please repost bank statement...lol

I have an older Pw2200, its a good unit. had it for a long time.

Im hoping for a bigger subwoofer.

+1 on this, I was thinking the exact same thing, table tuba with legs and a fake drawer. with a doily and a lamp.

hi there, and welcome. I recently had an issue with my KMC1. I call klipsch tech support, and they were really great. and able to help me through this. Typically, tech support will have already seen your issue, and know what the fix is...at least they did with mine. Give them a call.

I have also purchased all my pro stuff from spencer...he is great. I just ordered 3 more 510 horns from him. arrived a few days back.

Its going to look real nice in my living room. As someone else I know would say "Top Notch".