mike stehr Posted September 15, 2020 Share Posted September 15, 2020 Report post Posted 6 hours ago 09/14/2020 > SETI Said : A gift from IBSlammin. LuxmanPP triode 50ca10. Just completed cap replacement and putting it back to factory as it has been modified. Going to bring it up this week. I love the Luxman Me too... 3 Quote Link to comment Share on other sites More sharing options...
mike stehr Posted September 15, 2020 Share Posted September 15, 2020 2 Quote Link to comment Share on other sites More sharing options...
nikon f Posted September 15, 2020 Share Posted September 15, 2020 (edited) EL84 PP Motorola Amplifier. All out of spec resistors have been replaced, all caps including the can capacitor replaced. The power and output transformers are larger than a comparable Magnavox amp. Edited September 15, 2020 by nikon f 5 Quote Link to comment Share on other sites More sharing options...
charlieboy Posted September 15, 2020 Share Posted September 15, 2020 James Burgess PP 45 7 Quote Link to comment Share on other sites More sharing options...
henry4841 Posted September 16, 2020 Author Share Posted September 16, 2020 10 hours ago, charlieboy said: James Burgess PP 45 How many watts does it make being PP? Quote Link to comment Share on other sites More sharing options...
Marvel Posted September 19, 2020 Share Posted September 19, 2020 On 9/9/2020 at 12:00 AM, erik2A3 said: I know I mentioned this many moons ago, but hey....so what. Yes, but they could have simply put a cap on the plate and saved the expense of the extra tube and circuit. Quote Link to comment Share on other sites More sharing options...
Smitty8451 Posted September 21, 2020 Share Posted September 21, 2020 Here is mine, Rogue Audio RP-7 preamp, Atlas Magnum II amp, Rogue Audio Pharoah, Elekit TU-8800, and Tavish Adagio Phono pre with tube rectified power supply. 7 Quote Link to comment Share on other sites More sharing options...
MechEngVic Posted September 21, 2020 Share Posted September 21, 2020 4 hours ago, Smitty8451 said: Here is mine, Rogue Audio RP-7 preamp, Atlas Magnum II amp, Rogue Audio Pharoah, Elekit TU-8800, and Tavish Adagio Phono pre with tube rectified power supply. Do you have any speakers?😆 1 Quote Link to comment Share on other sites More sharing options...
Smitty8451 Posted September 21, 2020 Share Posted September 21, 2020 (edited) I have a dedicated room for all my upper end gear, here is a picture of the front end and home theater system. I have spent many years configuring my system and as it is now I can play any source on any amp via balanced matrix switches. La Scala AL5, RC-64 III, RB-61 II, RS-62 II, RS-52 II, DIY Rythmik Audio 1510 subs. Tubes only play to the La Scala. Edited September 21, 2020 by Smitty8451 Additional info 6 Quote Link to comment Share on other sites More sharing options...
Schu Posted September 22, 2020 Share Posted September 22, 2020 Amp cover pictures! 5 1 Quote Link to comment Share on other sites More sharing options...
A1UC Posted September 22, 2020 Share Posted September 22, 2020 Amp cover pictures! Who made that cover , I use to use a place but forgot name Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
Schu Posted September 22, 2020 Share Posted September 22, 2020 1 hour ago, A1UC said: Who made that cover , I use to use a place but forgot name I used someone on ebay... I just contacted them about doing a bespoke piece and explained what I wanted... thickness, width, height, length and that I wanted cutouts for the lift point and for the rear wire access. There are a few makers on the bay and most of them will do the work for you. I've had them for a while so I can't remember who it was exactly... but I've also done this for several turntables also, always with a different seller. Quote Link to comment Share on other sites More sharing options...
A1UC Posted September 22, 2020 Share Posted September 22, 2020 I used someone on ebay... I just contacted them about doing a bespoke piece and explained what I wanted... thickness, width, height, length and that I wanted cutouts for the lift point and for the rear wire access. There are a few makers on the bay and most of them will do the work for you. I've had them for a while so I can't remember who it was exactly... but I've also done this for several turntables also.I used https://stereosquares.com just found it , getting one made for my amp Sent from my iPhone using Tapatalk 2 Quote Link to comment Share on other sites More sharing options...
Smitty8451 Posted September 22, 2020 Share Posted September 22, 2020 I find keeping any equipment with top vents covered by acrylic covers really extends there service life not to mention as my wife says “they look like museum pieces, kinda like you”. No dust, no accidental knocking the tubes around and aesthetically pleasing to boot. 😁😁 Quote Link to comment Share on other sites More sharing options...
henry4841 Posted September 22, 2020 Author Share Posted September 22, 2020 Let's keep this thread running. I am sure there are lurkers that have tube amplifiers who have never posted. Now is the time to just post a picture and join in. I just like the looks of tube equipment glowing in the dark when listening to music. Romantic as well for you younger members. Quote Link to comment Share on other sites More sharing options...
Marvel Posted September 22, 2020 Share Posted September 22, 2020 Henry, Here are my Welborne Labs Moondog 2A3 amps, fired up under the table. Not a very good pic under there... Bruce 5 Quote Link to comment Share on other sites More sharing options...
Schu Posted September 22, 2020 Share Posted September 22, 2020 Oh... I'd love to try those. Quote Link to comment Share on other sites More sharing options...
henry4841 Posted September 22, 2020 Author Share Posted September 22, 2020 Beautiful wood. Maple? Quote Link to comment Share on other sites More sharing options...
Marvel Posted September 22, 2020 Share Posted September 22, 2020 Yes, it is. I may be selling these... been waffling for quite some time about it. 1 Quote Link to comment Share on other sites More sharing options...
seti Posted September 22, 2020 Share Posted September 22, 2020 I'm always trying to find ways of making point to point wiring look good. I bought these russian military surplus parts recently off ebay. Too cool... 1 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.