General Klipsch Info
Talk about any other Klipsch Audio products and accessories here.
21524 topics in this forum
-
- 8 replies
- 338 views
-
- 16 replies
- 266 views
-
- 4 replies
- 207 views
-
- 15 replies
- 686 views
-
- 5 replies
- 1.6k views
-
- 12 replies
- 303 views
-
- 7 replies
- 349 views
-
- 2 replies
- 219 views
-
- 3 replies
- 670 views
-
- 0 replies
- 219 views
-
- 2 replies
- 311 views
-
- 1 reply
- 251 views
-
- 3 replies
- 218 views
-
- 9 replies
- 265 views
-
- 1 reply
- 170 views
-
- 0 replies
- 166 views
-
- 25 replies
- 1.3k views
-
- 18 replies
- 235 views
-
- 0 replies
- 402 views
-
- 16 replies
- 6.9k views
-
- 1 reply
- 406 views
-
- 2 replies
- 249 views
-
- 9 replies
- 307 views
-
- 6 replies
- 197 views
-
- 2 replies
- 350 views
-
Recent Posts
-
-
By derrickdj1 · Posted
The question is not which tube to build an amp around, rather the design and execution. 300B, 2A3 and the other mentioned amps types can all be nice. Demo some amps is the best way or make it run multiple tubes. -
Did you solder or crimp your wires? I have not been able to find any female spades that can hold a 12 gauge speaker wire. -
I just used the spade connectors, just like Klipsch did in the Jubilee. -
I paired the Rp8000Fii's with my 70's Marantz 4240 and it was great! Treble is a little "less bright" and the mid range seemed to open up with more clarity. Bass was much more emphasized than with the old Pioneer that it was attached to. Are there any receivers anyone knows of that offer similar coloration to the old Marantzs? -
By Shakeydeal · Posted
Yeah I’d say .75 watt is a little low. Try a good 300B amp. That’ll git er done. -
.thumb.PNG.03e05fe1d4278d0fc5cd29558f68c9b1.PNG)
If I win. I’m taking these things on tour. I’ll rent theaters in cinemas and plant them down front. Give people a ‘listening experience’. Do this a few times state side, a few times overseas. Entertain the troops. Give the smoke people a table to imbibe or partake from and tune them up with 74 minutes of sound. It’s all Love. I’ll bring them with me for the Next KLIPSCH ‘Meet and Greet’. I would never bring them up the stairs to my apartment . I would instead Start a new adventure. There is a theater where I live. I have 16 weeks of ad space set. In September looking at theater space for HERESY II. A pre and amp w/o a house system. Just these speakers. * and for those that know the story already or for those that don’t. Vinyl test press was played on these speakers.. the produced the unique audio signal chain under the compression drivers for the Heresy II speakers. To achieve the ability of reproducing that experience my next objective. True, audio, listening experience. -
By RobMarshall · Posted
You have a beautiful system. Enjoy it to the fullest! -
By Travis In Austin · Posted
Check out the tubes section of the forum on ideas for tube amp builds also. -
@MMurg In your pic of the Celestion axi2050...what kind of connector does it use for your speaker wires? I purchased a pair direct from a Celestion dealer and they have a male spade. I hate the spade and am trying to find out what other connector might be available. I had a Allen's screw type banana jack for attaching to the spade and it is ok, but I would love to be able to have a direct spade or screw terminal instead.
-