Alerts!
Want to alert forum members to sales you are not affiliated with on eBay, Craigslist, etc? Post in here.
9165 topics in this forum
-
- 33 replies
- 1.8k views
-
- 33 replies
- 2k views
-
- 33 replies
- 2.1k views
-
- 33 replies
- 1.5k views
-
- 33 replies
- 9.5k views
-
- 33 replies
- 1.5k views
-
- 32 replies
- 1.8k views
-
- 32 replies
- 1.7k views
-
- 32 replies
- 2.6k views
-
- 32 replies
- 2.8k views
-
- 32 replies
- 3.3k views
-
- 32 replies
- 2.9k views
-
- 32 replies
- 85.9k views
-
- 32 replies
- 4.8k views
-
- 31 replies
- 1.7k views
-
- 31 replies
- 2.9k views
-
- 31 replies
- 1.5k views
-
- 31 replies
- 1.8k views
-
- 31 replies
- 1.7k views
-
- 31 replies
- 2.4k views
-
- 31 replies
- 1.8k views
-
- 31 replies
- 1.4k views
-
- 31 replies
- 1.8k views
-
- 31 replies
- 2.7k views
-
- 31 replies
- 5.3k views
-
Recent Posts
-
I've detected that one of my Khorns (early 80's) has a nasty buzz between 230 and 400hz. Not only is there a buzz, but also a noticeable volume difference. In other frequencies, they are pretty much the same, with no buzz. I swapped the K55v drivers and the problem followed the driver. I replaced the rubber gasket between driver and horn. Problem remained. I see that Crites has diaphragms available. Is that my likely path to solving this? I've replaced diaphragms before, so I'm not scared of the project, unless there is something uniquely challenging? I've read some forum posts that suggest sound quality improves with new diaphragms, being that the old are brittle by now. Anyone confirm this? Thanks for any direction or input. -
-
Of the options listed, I’ve heard many good things about matching Klipsch with NAD and Cambridge Audio.
-
Are you sure that 6 isn’t a G or an S? Post a pic of the tag.
-
By tube fanatic · Posted
Two excellent solo performances with Hour of Power choir Maynard -
-
.thumb.JPG.e865cb9742a8f1a873e5b238842d7c3f.JPG)
Not mine, no affiliation, no interest.... https://www.facebook.com/marketplace/item/3576880255894633/ For posterity... -
By vonelliott · Posted
Hi all, ended up selling them in less than 24 hours to someone for $3250 though I had several other buyers interested in coming by for $3500. Thanks for all the input! -
Lagging -- One method to use is with a distribution panel and impedance matching volume controls. I used this in a previous house, two speakers at the patio and two in the kitchen ceiling. Used a Dayton class D amp. Had a 4 post speaker wall panel that had multiple outputs on the rear. Run speaker connections to the volume control (one for each set of speakers) and then on to the speakers. Set the number of speakers/load at the volume control. Powered all four with a Dayton class D amp. Am doing the same at the house we just moved to. Using a monoprice 8 pair distribution panel. Feed that with a Aiyima A7 amp. From the left - distribution panel - Aiyima - amp power - DAC - not seen raspberry Pi Only the porch speakers wired currently, the kitchen is being renovated starting in a few week so hope to have the ceiling speakers install in the next couple of months. The raspberry runs a spotify connect client (raspotify) so I can run things from my phone (via the LAN) or use RDP to use VLAN to play ripped tunes from the connected USB SSD -
-